yes they are good brickworx uses them on almost all his cars
3-2 is better then 3-1
and lcb and an rc40 are a good mix ask willy
| ausmini https://www.ausmini.com/forums/ |
|
| lcb to rc40? https://www.ausmini.com/forums/viewtopic.php?f=2&t=6756 |
Page 1 of 1 |
| Author: | benjamin [ Fri Apr 29, 2005 8:24 pm ] |
| Post subject: | lcb to rc40? |
i have a 1 3/4 rc40 exhuast and want to fitsome lcb extractors, brickworx is selling some on ebay and i want to know if they fit but he never replied it is now a day till it finishes and i need an aswer can anybody help http://cgi.ebay.com.au/ws/eBayISAPI.dll ... 19099&rd=1 |
|
| Author: | bigel nigel [ Fri Apr 29, 2005 8:45 pm ] |
| Post subject: | |
any zorst place should be able to make it fit just depends on the place you got to go to a good place get a nice good fit go to a bad place get a bad fit maybe with a leak |
|
| Author: | drmini in aust [ Fri Apr 29, 2005 8:46 pm ] |
| Post subject: | |
Yes, they are right size & should fit if you use the right link pipe. Any exhaust place can make one up if needed. |
|
| Author: | benjamin [ Fri Apr 29, 2005 8:47 pm ] |
| Post subject: | |
also is that worth it and are they any good? |
|
| Author: | bigel nigel [ Fri Apr 29, 2005 8:49 pm ] |
| Post subject: | |
yes they are good brickworx uses them on almost all his cars 3-2 is better then 3-1
and lcb and an rc40 are a good mix ask willy |
|
| Author: | drmini in aust [ Fri Apr 29, 2005 8:52 pm ] |
| Post subject: | |
$130 is pretty cheap, They look similar in pic to a Perry LCB. Those are OK on small bore motors, on big bores I'd rather a Maniflow one. Or a Brownrigg. But both cost heaps more $$. |
|
| Author: | benjamin [ Fri Apr 29, 2005 8:53 pm ] |
| Post subject: | |
so it should be ok on my 1144 |
|
| Author: | drmini in aust [ Fri Apr 29, 2005 8:55 pm ] |
| Post subject: | |
benjamin wrote: so it should be ok on my 1144
Yep. |
|
| Author: | benjamin [ Fri Apr 29, 2005 8:57 pm ] |
| Post subject: | |
please no one else bid i can just afford these |
|
| Author: | Spaceboy [ Fri Apr 29, 2005 9:28 pm ] |
| Post subject: | |
i had a set of these on on of my old cars, they're at the bottom end as far as lcb's go, and they are an absolute biatch to fit properly and will make your exhaust go at a funny angle. still a lot better than the standard manifold |
|
| Author: | willy [ Sat Apr 30, 2005 1:10 am ] |
| Post subject: | |
I would advise against the Wildcats. Please if you have the funds, go proper LCBs. Wildcats are cheap imitations; don't fit right and require "bashing" (literally) to get them to fit. So yeah, buy some decent LCBs and not the Wildcats. |
|
| Page 1 of 1 | All times are UTC + 10 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|