Ausmini
It is currently Thu Jul 09, 2020 3:34 pm

All times are UTC + 10 hours




Post new topic Reply to topic  [ 350 posts ]  Go to page Previous  1 ... 20, 21, 22, 23, 24
Author Message
PostPosted: Wed May 06, 2020 10:30 pm 
Offline
998cc
998cc
User avatar

Joined: Mon Jan 16, 2006 1:15 pm
Posts: 670
Location: Melbourne
Nice work there Mearcat. Great attention to detail as always, this is going to look great when finished.

Cheers
Madmorrie


Top
 Profile  
 
 Post subject: Re:
PostPosted: Wed May 20, 2020 2:07 am 
Offline
848cc
848cc

Joined: Sat Feb 16, 2008 6:01 am
Posts: 42
Location: Santiago, Chile
Mearcat wrote:
I completed the support bracket for the equalising driveshaft / layshaft today. The bracket pieces were laser cut from 10mm steel and their minimum charge, I got 3 sets cut - both of the spare sets have been pre-sold to Joe (blue_deluxe) and a local guy here in Perth - both doing the 4EFTE conversion!

The design was based on the one made by Slinkey (thanks! :D ). The two main pieces bolt onto the shaft itself; and rear of the engine block (where the alternator used to be).
Image

Image

Image


The top part of the larger piece was bent to clear the centre bolt hole in the smaller piece. My arc welder was cranked right up for the 10mm steel and it was all welded up with a couple of gussets for bracing.
Image

Next step - replace my front valance panel (current one is bashed up and bent to sh!t) and complete the subframe design.




Hi Mearcat, sorry to bother you, which car did you get the equalising layshaft?

thanks and cheers from Chile

Axel

_________________
Image


Top
 Profile  
 
 Post subject: Re: Re:
PostPosted: Wed May 20, 2020 11:12 am 
Offline
998cc
998cc
User avatar

Joined: Tue Nov 13, 2007 4:17 pm
Posts: 898
Location: NOR, Perth, W.A.
clubman S wrote:
Hi Mearcat, sorry to bother you, which car did you get the equalising layshaft?
thanks and cheers from Chile
Axel

The equaliser shaft/layshafts are from a AE101 or AE111 Corolla/Levin with 4AGE engine. Of course, I have no idea how accessible those cars/parts are in Chile but good luck.

_________________
-Alan
I blame my dad for my love of minis. I think I was conceived in the back seat of one :D
I also blame my Dad for me being 6' 1" - not really the optimum height for driving a Mini.


Top
 Profile  
 
 Post subject: Re: Re:
PostPosted: Thu May 21, 2020 4:31 am 
Offline
848cc
848cc

Joined: Sat Feb 16, 2008 6:01 am
Posts: 42
Location: Santiago, Chile
Mearcat wrote:
clubman S wrote:
Hi Mearcat, sorry to bother you, which car did you get the equalising layshaft?
thanks and cheers from Chile
Axel

The equaliser shaft/layshafts are from a AE101 or AE111 Corolla/Levin with 4AGE engine. Of course, I have no idea how accessible those cars/parts are in Chile but good luck.

thanks!!!


brgds
AJ

_________________
Image


Top
 Profile  
 
 Post subject:
PostPosted: Mon Jun 29, 2020 12:39 pm 
Offline
998cc
998cc
User avatar

Joined: Tue Nov 13, 2007 4:17 pm
Posts: 898
Location: NOR, Perth, W.A.
Once again, here are a few updates form the last few months...

My focus is now on the interior of the Mini and I wanted to make a centre console to hide the gear shifter. Before that, I had to move the handbrake rearward as it was too close to the gear shifter assembly.
Image
I cut off the factory bent-steel mount and made a beefier one (with captive nuts) that won't eventually crack like a lot of mounts I've seen.
Image
This was stitch welded back on 50mm further back
Image

At 150mm wide, I purposely made the centre console as narrow as possible to maximise legroom. It was a basic design made from MDF and covered in a few layers of fibreglass to make the surface more resistant to knocks/dents.
Image
Image
For mounting the gear shifter boot, I made a frame that screws to the inside of the centre console. The boot will eventually screw into this frame
Image
In the console, I have a voltmeter, power window switches and a small plastic storage tray (from a Toyota Tacoma)
Image
The original plan was to have a cigarette lighter and USB outlets in the console but I didn't end up with enough room so I mounted them either side of the stereo.
Image

...and speaking of power windows, I bought a SPAL power window kit years ago and it was now time to install the motors. With one end of the motor mechanism attached to the window winder, the other end would fit nicely in the door skin opening and not interfere with the window glass or mechanism as the motor would sit directly below the 1/4 window in the door.
Image
I had to make a custom spacer to stop the handle adapter cog thing from moving back/forth on the winder shaft
Image
Image
Like most power window kits, they some with those triangular / cheese wedge brackets but I wanted something neater than self tapping screws into the door so some more custom brackets were made
Image
Mounted like this (screwed into rivnuts in the door) , apart from the winder handle that sticks out about 40mm, the rest of the power window mechanism only sits at most 5-6mm proud of the door skin and and no cutting of the door required.
Image

_________________
-Alan
I blame my dad for my love of minis. I think I was conceived in the back seat of one :D
I also blame my Dad for me being 6' 1" - not really the optimum height for driving a Mini.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 350 posts ]  Go to page Previous  1 ... 20, 21, 22, 23, 24

All times are UTC + 10 hours


Who is online

Users browsing this forum: No registered users and 6 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  

© 2016 Ausmini. All garage work involves equal measures of enthusiasm, ingenuity and a fair degree of irresponsibility.