ausmini
https://www.ausmini.com/forums/

Round nose efte (updated pg 6 - 04.01.07)
https://www.ausmini.com/forums/viewtopic.php?f=23&t=18264
Page 2 of 13

Author:  Baracade [ Thu May 25, 2006 12:35 pm ]
Post subject: 

Dan,

I cant beleive thats the same rear end!

Dam turned out nice.. Well done..

Dam radiator & everything is looking awesome!

Author:  Stuwey [ Thu May 25, 2006 12:36 pm ]
Post subject: 

Mate, that thing looks bloody awesome. I love the old-style pastel paintjob, the wheels suit it perfectly, too.

However, the fuel system in the boot is just perfection. I love seeing that some real effort went into it, and it looks every part of it. Well done.

Would a s,all scoop below the rad help???

Author:  minimetoy [ Thu May 25, 2006 12:49 pm ]
Post subject: 

I want to try out the rad before i go down the road of putting a scope on.

However i did notice a truck today with a rad mounted exactly the same way but it was at the front. It had a rubber dam on three sides todirect the air in.

Dan

Author:  GTi_Mini [ Thu May 25, 2006 12:54 pm ]
Post subject: 

I have got to say thats one of the neatest rear ends I have seen. Love the fuel system and the radiator mounted underneath. cant wait to see the finished product. quality work. pure quality.

Author:  JC [ Thu May 25, 2006 9:34 pm ]
Post subject: 

Looking good Dan, looking good.

Do you think that radiator will disperse enough heat? I would think that a fair amount of the heat would also be lost in the pipe to the radiator.

How do you fill it and how does air/bubbles get out?

Author:  marcsvenson [ Fri May 26, 2006 9:24 am ]
Post subject: 

thats one sweet piece of ace :lol:

awesome work

Author:  Fat Boy Dave [ Fri May 26, 2006 1:25 pm ]
Post subject: 

Just a query, but how do you keep the radiator clear of mud and dirt?

Quality of finish looks excellent though.

speedhumps will be a bitch though.

Author:  dove grey 64 [ Fri May 26, 2006 2:00 pm ]
Post subject: 

great quality work so far, keep it up.

Author:  998_Clubman [ Fri May 26, 2006 5:09 pm ]
Post subject: 

awesome job there mate! looks very neat and tidy in the boot, rad is differnet, never seen on there before, looks the part!!!

keep up the good work, exhaust looks good 8)

Author:  minimetoy [ Thu Jun 29, 2006 5:07 pm ]
Post subject: 

Picked up my new clutch from MRC today. Its a Soft Button clutch that acts like normal clutch but can take a beating like a brass button clutch. It is made from two plates that act like a cushion hence stopping the straight out grab factor.

The pressure plate is rated at 800kg.

I can't wait to give it a go.

Dan

Author:  Mini Mad [ Thu Jun 29, 2006 10:31 pm ]
Post subject: 

emmachizit?

Author:  Baracade [ Fri Jun 30, 2006 8:23 am ]
Post subject: 

Hmm saw this clutch when i was at MRC... Very intresting.. You are one of the first to be using it out here Dan.... Very very very intresting...

I have a dam brass button....

Author:  minimetoy [ Sun Aug 06, 2006 7:51 pm ]
Post subject: 

As requested by Matt, update photos.

Image

Image

Image

Image

Image

This is my soft button clutch. Note the twin plate set up which allows you drive the car normally through traffic but also thrash it when required. the pressure plate is rated to 830kg.

Image

Image

Image

Dan

Author:  awdmoke [ Sun Aug 06, 2006 8:55 pm ]
Post subject: 

Damn! Looking good 8)

Author:  harvey69 [ Sun Aug 06, 2006 8:58 pm ]
Post subject: 

looking good alright !

Page 2 of 13 All times are UTC + 10 hours
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/