simular to my mazda 626 turbo seats sept they were 100 and did not need trimming
makka

_________________
Anonymous moderation means the agro that is built up towards the mods isn't aimed at an individual (fewer "Makk" attacks). Less stress for mods means less moderator "retirements".

They didn't fit temporarily bolted them in but couldn't close the door... too wide, door bin hit them. Sold them for $10 more than I bought them for

A year later ...

I just got a pair of Autotecnica SP6 Monza recliner's for my Clubby.
Black/grey discontinued model - $400 the pair from Repco.
The're 57cm wide - JUST fit!!
I think I'll have to "coax" the sholder supports in 1 cm to clear the rubber door surround.
fortunately these sit nicely into the widest part of the car,
and the bases clear the rear bins nicely - very comfy.
I haven't fitted them properly yet - gotta finish the spray job first!

I read it was illegal to fit non reclining seats in a 2 door with back seats fitted!

_________________
"Why mini? 'cause it's got the edge."

these are my seats,
bought them of ebay for $350 plus postage, theyre pretty damn comfy and look pretty sweeet

_________________
-jamie-
1963morris 850
1965 solid side van
1994 rover racecar

sorry to hijack thread but page one dani 's pic hottie and ausmini hotest member contest going

wat???

shes very hot though ay!!!

(watch out for danidad!!!!!!!

_________________
-jamie-
1963morris 850
1965 solid side van
1994 rover racecar

mmm, and at her age could land you in very HOT water!

Back to the subject: here's my spanking new seats ...

Yet to be fitted
BTW, I like the Pirahana's - look narrower across the shoulder than these!

_________________
"Why mini? 'cause it's got the edge."

why how old is she????

seets look sweeeet mate

_________________
-jamie-
1963morris 850
1965 solid side van
1994 rover racecar

well, a year ago she was 14, so Im guessing she's had a birthday.
I have 2 of my own, but I aint introducing them to this forum!!
There a tad younger than that, but given the comments ...

_________________
"Why mini? 'cause it's got the edge."

he he me cant get into much trouble!!!

im only 16 bahahahahaahahahahaa

im glad i like minis.....

_________________
-jamie-
1963morris 850
1965 solid side van
1994 rover racecar

You lucky boy!!!!
My dad alway said:
"you're only as old as the woman you feel".
Not sure what he meant by that

_________________
"Why mini? 'cause it's got the edge."

Can't remember if i posted my finished pics in this thread... these are my seats.

_________________
- Simon -

mad mk1 i would not be concerned with her age
i'd be more concerned if her father who frequents here took offence ...
i would ok so you have commented done your pre pubesent load oin yer undies get over it
makka

_________________
Anonymous moderation means the agro that is built up towards the mods isn't aimed at an individual (fewer "Makk" attacks). Less stress for mods means less moderator "retirements".

Here's some pics of my OBX Torino's. $800 for the pair, bloody nice seats though. Did the subframes up myself. Also bought a pair of Suzuki Swift seat rails and rejigged them for the OBX's.

_________________
225hp atw on 14psi. 1/4 Mile no idea. Take one 1971 Mini Clubman, one Starlet GT Halfcut, Simmer over a warm MIG Welder, and Voila Minstar! www.mpdesign.id.au

Those Torino's look comfy!!
How much were the Swift Rails?

The Autotecnica Monzas were too wide at the shoulders
BUT, luckily, they have a ~1cm round metal bar which follows the contours on the sides,
which is covered with foam - not fibreglass wings like the replacement model.
I got a peek under a velcro bit at the side, and didn't have to pull the covers off!
With a little gentle persuasion using a sash clamp, I have managed to coax them in
around 4cm - enough to fit !
Fortunately, I still fit in them too!!

_________________
"Why mini? 'cause it's got the edge."