Ausmini
It is currently Sun Jul 20, 2025 8:06 am

Board index » Mini Chat » Mini Chat

All times are UTC + 10 hours




Post new topic Reply to topic  Page 2 of 2
  [ 22 posts ]  Go to page Previous  1, 2
  Print view Previous topic | Next topic 
Author Message
timmy201
PostPosted: Fri Jul 07, 2017 4:51 pm 
Offline
1275cc
1275cc
User avatar

Joined: Sun Apr 29, 2012 1:19 pm
Posts: 4501
Location: Wollongong, NSW
8700s14 wrote:
phillb wrote:
8700s14 wrote:
Also, another question: I measured my belt (well, the belt off the car, not the one around my waist) and it is about 810mm, I see there are three common sizes of 813, 825 and 850mm, the 'cooper s mk1' should be suited to the 850mm belt (larger water pump pulley), what should the diameter of the cooper s water pump pulley be?


The Cooper S had a larger generator pulley than standard I think (to reduce generator rpm at high engine rpm. Not sure about the water pump pully, I thought that was the same.


Sent from my iPhone using Tapatalk


I use this as an example for why I am led to believe the cooper s had a larger water pump pulley:
http://www.classicmotoring.net.au/cmos/index.php?main_page=product_info&cPath=37_156&products_id=37

A couple are listed here:

http://www.somerfordmini.co.uk/eshop/in ... page&id=97


You do not have the required permissions to view the files attached to this post.

_________________
Image
Top
 Profile  
 
gtogreen1969
PostPosted: Fri Jul 07, 2017 6:23 pm 
Offline
1275cc
1275cc
User avatar

Joined: Fri May 02, 2008 3:07 pm
Posts: 5123
Location: The Internet
8700s14 wrote:
phillb wrote:
8700s14 wrote:
Also, another question: I measured my belt (well, the belt off the car, not the one around my waist) and it is about 810mm, I see there are three common sizes of 813, 825 and 850mm, the 'cooper s mk1' should be suited to the 850mm belt (larger water pump pulley), what should the diameter of the cooper s water pump pulley be?


The Cooper S had a larger generator pulley than standard I think (to reduce generator rpm at high engine rpm. Not sure about the water pump pully, I thought that was the same.


Sent from my iPhone using Tapatalk


I use this as an example for why I am led to believe the cooper s had a larger water pump pulley:
http://www.classicmotoring.net.au/cmos/index.php?main_page=product_info&cPath=37_156&products_id=37

That should read "larger dynamo pulley". The water pump pulley was the standard one used by the other models.
Top
 Profile  
 
drmini in aust
PostPosted: Fri Jul 07, 2017 6:51 pm 
Offline
religious status
religious status
User avatar

Joined: Fri Mar 19, 2004 6:19 pm
Posts: 39754
Location: near Baulkham Hills, NSW
8700s14 wrote:
drmini in aust wrote:
I would remove the radiator hoses, refit water pump, plug water pump inlet. Then fill to top of head with 1:3 molasses and water mix. Leave 2 or 3 weeks, remove water pump and welch plugs then hose out. Fit new water pump and welch plugs.
I have an S motor on the floor getting this treatment. ;)

I've done this before so I know it works.


I had thought of doing so, but was worried about washing it out afterwards. Does washing it out with the garden hose afterward actually get all the softened crud out?


Yes it does. Garden hose works, a karcher or similar is even better.

Before filling I remove the hex plug at back corner of the block and twiddle a drill bit in there. Then after draining, aim the hose in there too.
I generally stand the block on it's back and fill to the water pump hole, with the head on. But I don't see why this won't work in the car.

_________________
DrMini- 1970 wasaMatic 1360, Mk1S crank, 86.6HP (ATW) =~125 @ crank, 45 Dellorto (38 chokes), RE282 sprint cam, 1.5 rockers, 11.0:1 C/R. :mrgreen:
Top
 Profile  
 
simon k
PostPosted: Fri Jul 07, 2017 7:11 pm 
Offline
Yay For Hay!
User avatar

Joined: Wed Sep 08, 2004 9:27 pm
Posts: 15912
Location: Wodonga - Vic/NSW border
I'd be really concerned about the condition of the bearings after sitting for so long... engine oil turns acidic, and left on the bearings will eat them away...

take it out and off the gearbox, you'll probably get away with putting new rings and bearings in it & not a full rebuild

_________________
did I tell you that I won a trophy?
Top
 Profile  
 
8700s14
PostPosted: Fri Jul 07, 2017 7:45 pm 
Offline
848cc
848cc

Joined: Thu May 11, 2017 9:23 pm
Posts: 298
simon k wrote:
I'd be really concerned about the condition of the bearings after sitting for so long... engine oil turns acidic, and left on the bearings will eat them away...

take it out and off the gearbox, you'll probably get away with putting new rings and bearings in it & not a full rebuild


I was planning on taking the 'fingers crossed' approach. :lol:
Top
 Profile  
 
simonw
PostPosted: Fri Jul 07, 2017 9:31 pm 
Offline
998cc
998cc
User avatar

Joined: Wed Jul 08, 2015 3:29 pm
Posts: 857
Location: Brisbane QLD
Phosphoric acid . Getsrid of the rust . Flush out after 20 mins.


Sent from my iPad using Tapatalk

_________________
Simonw
Brisbane QLD
1st car - 1964 Mini Panelvan 850
Previous - 1978 Leyland LS 1275 Gold
- 1969 Mini K
Top
 Profile  
 
8700s14
PostPosted: Fri Jul 07, 2017 11:14 pm 
Offline
848cc
848cc

Joined: Thu May 11, 2017 9:23 pm
Posts: 298
simonw wrote:
Phosphoric acid . Getsrid of the rust . Flush out after 20 mins.


Sent from my iPad using Tapatalk


I do like the idea of using a converter for the potential benefit of having it hold off the re-forming of rust.
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 2 of 2
  [ 22 posts ]  Go to page Previous  1, 2

Board index » Mini Chat » Mini Chat

All times are UTC + 10 hours


Who is online

Users browsing this forum: No registered users and 78 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  

© 2016 Ausmini. All garage work involves equal measures of enthusiasm, ingenuity and a fair degree of irresponsibility.