ausmini https://www.ausmini.com/forums/ |
|
2 Speed Wiper Wiring https://www.ausmini.com/forums/viewtopic.php?f=2&t=101362 |
Page 1 of 2 |
Author: | cooperess [ Fri May 27, 2022 2:29 pm ] |
Post subject: | 2 Speed Wiper Wiring |
Attachment: 2 Speed Wiper Connector 1306.JPG Looking for help on how to remove the wiring so I can rewire. If this is not possible, where can I get this fitting? |
Author: | TDS76 [ Fri May 27, 2022 3:09 pm ] |
Post subject: | Re: 2 Speed Wiper Wiring |
You need to move the crimp locking tab down with a small screwdriver so that the crimp can be pulled out. The photo shows the one with a tab on the left and a non-locking one on the right. Attachment: Female 0.25 Locking.jpg
|
Author: | winabbey [ Fri May 27, 2022 10:33 pm ] |
Post subject: | Re: 2 Speed Wiper Wiring |
One of those tiny flat screwdrivers helps in getting access to the tang. |
Author: | ozmini [ Sat May 28, 2022 6:57 am ] |
Post subject: | Re: 2 Speed Wiper Wiring |
the stainless strips that are in some wiper blades are also useful - NB there are 2 widths and the narrower one is the best. I have found that these strips do less damage to the plug than the screwdriver. |
Author: | cooperess [ Sat May 28, 2022 9:19 am ] |
Post subject: | Re: 2 Speed Wiper Wiring |
It too difficult to remove the pins. Where are can I get a replacement plastic connector? |
Author: | Bill B [ Sat May 28, 2022 11:46 am ] |
Post subject: | Re: 2 Speed Wiper Wiring |
Neither my mid- '69 mini K (single speed) nor 8/70 S (2 speed) have the terminal block. The wiring ends in those moulded black plastic insulators, so they are factory original. |
Author: | cooperess [ Sat May 28, 2022 12:45 pm ] |
Post subject: | Re: 2 Speed Wiper Wiring |
Maybe my wipers are only single speed. LUCAS AUSTRALIA 62971039A 12AUW 4-69 with 4 wires 110 Degree. |
Author: | winabbey [ Sat May 28, 2022 12:48 pm ] |
Post subject: | Re: 2 Speed Wiper Wiring |
Bill B wrote: Neither my mid- '69 mini K (single speed) nor 8/70 S (2 speed) have the terminal block. The wiring ends in those moulded black plastic insulators, so they are factory original. This shows the moulded black plastic connectors on my 8/70 S with 2 speed wipers that Bill is talking about. Well, at least the remains after rats had feasted on the wiring insulation. The moulded connector block appeared sometime in the Clubman/Leyland Mini era. Attachment: Wiper Motor connectors.jpg
|
Author: | winabbey [ Sat May 28, 2022 12:50 pm ] |
Post subject: | Re: 2 Speed Wiper Wiring |
cooperess wrote: Maybe my wipers are only single speed. LUCAS AUSTRALIA 62971039A 12AUW 4-69 with 4 wires. Four wires suggest two-speed wipers. The first production use was on SPO41 cars from 8/70, so yours may have been fitted by a previous owner. |
Author: | cooperess [ Sat May 28, 2022 1:02 pm ] |
Post subject: | Re: 2 Speed Wiper Wiring |
The cover suggests one speed. |
Author: | winabbey [ Sat May 28, 2022 1:12 pm ] |
Post subject: | Re: 2 Speed Wiper Wiring |
cooperess wrote: The cover suggests one speed. Wrong cover? Is the wiper switch a two-speed type? |
Author: | Bill B [ Sat May 28, 2022 2:08 pm ] |
Post subject: | Re: 2 Speed Wiper Wiring |
winabbey wrote: This shows the moulded black plastic connectors on my 8/70 S with 2 speed wipers that Bill is talking about. Well, at least the remains after rats had feasted on the wiring insulation. The moulded connector block appeared sometime in the Clubman/Leyland Mini era. That would make sense to incorporate a terminal block for the harness once 2-speed motors became standard and not just used in special production runs. My single speed Lucas Aust motor only has 3 terminals on the motor and 3 wires attached to them so 4 terminals is a good indication of being 2-speed. |
Author: | cooperess [ Sat May 28, 2022 2:11 pm ] |
Post subject: | Re: 2 Speed Wiper Wiring |
Wrong cover? That's my thinking. Is the wiper switch a two-speed type? I have bought a 2 speed switch thinking is a 2 speed wiper. |
Author: | ausdino [ Sat May 28, 2022 7:53 pm ] |
Post subject: | Re: 2 Speed Wiper Wiring |
Three wiper wires with black terminals from my 3/70 S wiring loom. Originally it also had a single speed wiper and switch. I have modified a spare wiper motor to be two speed and have bought a two speed switch. I will probably just add and extra wire (with black terminal) to make the 2 speeds work - will look more original. The other pictures show the clubman 4 pin plug and loom I bought ages ago, which is the same as the plug you pictured. |
Author: | cooperess [ Sat May 28, 2022 8:35 pm ] |
Post subject: | Re: 2 Speed Wiper Wiring |
I just made a connector removal tool with a modified hack saw blade. Attachment: Mini Wiper Connector Tool Hack Saw Blade DSCF1313.JPG
|
Page 1 of 2 | All times are UTC + 10 hours |
Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |