This is the Contact I have and will be doing the same Shortley
| ausmini https://www.ausmini.com/forums/ |
|
| Delorto parts? https://www.ausmini.com/forums/viewtopic.php?f=2&t=10819 |
Page 1 of 2 |
| Author: | clubmn [ Mon Sep 05, 2005 6:10 pm ] |
| Post subject: | Delorto parts? |
Where can i get some Delorto parts? Im trying to tune an engne, Does anyone have some jets etc. that they may want to hire. Or know of a place that stock Parts. Also i need 4 Idle screws suit Delorto...Email [email protected] If you can help |
|
| Author: | gafmo [ Mon Sep 05, 2005 7:14 pm ] |
| Post subject: | |
This is the Contact I have and will be doing the same Shortley
|
|
| Author: | drmini in aust [ Mon Sep 05, 2005 7:20 pm ] |
| Post subject: | |
Carburettor Service Co, 240 Parramatta Rd Burwood (Sydney) carry jets and repair kits. Or, try this guy- 
Otherwise, bring in bits from Eurocarb, at www.dellorto.co.uk like I do.
|
|
| Author: | feralsprint [ Mon Sep 05, 2005 7:22 pm ] |
| Post subject: | |
try this link, they have been good in the past and it only takes about 4-5 days for the bits you need to arrive, i had lots of problems getting the right emulsion tubes and jets in oz and finally had to resort to these guys [email protected] its there email addy and if you know what you want thaey are good 
|
|
| Author: | drmini in aust [ Mon Sep 05, 2005 7:44 pm ] |
| Post subject: | |
They will send you a parts list with prices. I use them too, as I said above. But they may try to steer you to their local distributor here... 
|
|
| Author: | feralsprint [ Mon Sep 05, 2005 7:57 pm ] |
| Post subject: | |
Doc yeah last time I posted on here when someone was looking for emulsion tubes in canberra I ended up getting an email from a guy in the US looking for tubes 7774.5 and he wanted 6, thanks for putting up that link to the Australian dealer i really couldn't find anyone a couple of years ago with a good range of bits in oz |
|
| Author: | drmini in aust [ Mon Sep 05, 2005 8:02 pm ] |
| Post subject: | |
Just so you know, 7772.5 emulsion tubes are NLA now I think- but 7772.6 work OK for me, in 1098s and 1275s.
|
|
| Author: | feralsprint [ Mon Sep 05, 2005 8:09 pm ] |
| Post subject: | |
Doc I got 4 if ya ever need em, they weren't right for the dolomite when I put the twins on it have gone the next size up and will probably end up going up again and after that there ain't no where to go
|
|
| Author: | clubmn [ Mon Sep 05, 2005 8:24 pm ] |
| Post subject: | thanks |
Thanks for the help guys, Im trying to tune my 1500 cortina/bugeye But i know not a thing about Dell'Ortos carbies. The numbers provided should help me out. If anyone has any sudgestions for combinations for a starting point, I would be very intrested to hear. |
|
| Author: | drmini in aust [ Mon Sep 05, 2005 9:23 pm ] |
| Post subject: | Re: thanks |
clubmn wrote: Thanks for the help guys, Im trying to tune my 1500 cortina/bugeye But i know not a thing about Dell'Ortos carbies. The numbers provided should help me out.
If anyone has any sudgestions for combinations for a starting point, I would be very intrested to hear. What size carb(s), single or twins? |
|
| Author: | gafmo [ Mon Sep 05, 2005 9:50 pm ] |
| Post subject: | |
Good I'm a dope sometimes...Ekk Yer mine was the Uk Deelorto site also http://www.dellorto.co.uk/... some body give me a thick head please |
|
| Author: | CPOCSM [ Mon Sep 05, 2005 10:16 pm ] |
| Post subject: | |
I have about 20 of each (emulsion tubes .5, .6, .7, idle jets, mains, pump jets and air correctors). Cost me around $120 and all new. Near on bought them out. Mob in italy still selling the stuff - waiting on some 30mm chokes - just to see what happens when I put them in Henry Hooroo Rob Forsyth Miniot!! |
|
| Author: | gafmo [ Mon Sep 05, 2005 10:20 pm ] |
| Post subject: | |
By chance do you have any butterflies for a 40 and a 48 including shaftes and bearings...Ant of the above I will purchase
|
|
| Author: | clubmn [ Mon Sep 05, 2005 10:32 pm ] |
| Post subject: | Delorto |
twin 40's (2) . |
|
| Author: | CPOCSM [ Mon Sep 05, 2005 10:35 pm ] |
| Post subject: | |
gafmo wrote: By chance do you have any butterflies for a 40 and a 48 including shaftes and bearings...Ant of the above I will purchase
No shafts or bearings - wait until i get the stuff in and I will see what I have - I am not really interested in cash - more to help those in need...lol I think they cost me all of $2.50 a piece...chicken feed... Will let you know when the stuff gets in Hooroo Rob Forsyth Miniot!! |
|
| Page 1 of 2 | All times are UTC + 10 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|