He can't be stuffed doing so his slave has to...But he is Sick...so I'm feeling Generous...
Yer good one Dody with the little Pic
Should Fit Nicley behind the Grill
| ausmini https://www.ausmini.com/forums/ |
|
| Cody Got Bling https://www.ausmini.com/forums/viewtopic.php?f=2&t=11705 |
Page 1 of 3 |
| Author: | gafmo [ Fri Sep 30, 2005 6:49 pm ] |
| Post subject: | Cody Got Bling |
He can't be stuffed doing so his slave has to...But he is Sick...so I'm feeling Generous... Yer good one Dody with the little Pic
Should Fit Nicley behind the Grill
|
|
| Author: | GT1360 [ Fri Sep 30, 2005 6:53 pm ] |
| Post subject: | |
 yep... thats my bling bling intercooler.  760x300x76 
|
|
| Author: | sg [ Fri Sep 30, 2005 6:58 pm ] |
| Post subject: | |
you modifying it into a radiator........................ 
|
|
| Author: | JC [ Fri Sep 30, 2005 7:06 pm ] |
| Post subject: | |
ah..er....where is you think that's going to fit? |
|
| Author: | GT1360 [ Fri Sep 30, 2005 7:15 pm ] |
| Post subject: | |
easy fit behind the gril.. no dizzy.. edis programable ignition
|
|
| Author: | drmini in aust [ Fri Sep 30, 2005 8:17 pm ] |
| Post subject: | |
Hmmmm so where's the oil cooler go, you might need one with all this power heating the oil up! 
|
|
| Author: | Stuartminidlx [ Fri Sep 30, 2005 8:24 pm ] |
| Post subject: | |
good point doc. i am thinking of maybe a custom made largers oil cooler or twin 13 row coolers. i think i am goin to use a s13 intercooler. also |
|
| Author: | GT1360 [ Fri Sep 30, 2005 8:35 pm ] |
| Post subject: | |
oil cooler will go out the side. I cot no inner gaurds remember.. can mount on the brace bars.
|
|
| Author: | kazjim [ Fri Sep 30, 2005 8:37 pm ] |
| Post subject: | |
And Altenator, and Starter, and . . . . Been there.. no room ...... Sorry mon, it no fittee ..... Unless you move your engine back about 2" then there may just be enough squeeze . . . J |
|
| Author: | GT1360 [ Fri Sep 30, 2005 8:38 pm ] |
| Post subject: | |
with no dizzy there is room 
|
|
| Author: | kazjim [ Fri Sep 30, 2005 8:54 pm ] |
| Post subject: | |
You have a Starter Motor in there ? Hmmmmmmmm cant fit a pack of cards between my chassis rail and the starter...... J |
|
| Author: | JC [ Fri Sep 30, 2005 8:55 pm ] |
| Post subject: | |
I'm certainly not a defeatist but it don't rate your chances. I'll be glad to be proven wrong. Where are you mounting the turbo? |
|
| Author: | GT1360 [ Fri Sep 30, 2005 9:08 pm ] |
| Post subject: | |
turbo down the back of the block... it will fit.. TRUST ME. nothing like a little cutting and shuting 
|
|
| Author: | drmini in aust [ Fri Sep 30, 2005 9:13 pm ] |
| Post subject: | |
My S oil cooler has only 3mm clearance to the Lucas starter, and it's nowhere near 75mm thick. I had to pack the grille out to clear. I used surplus Pulsar dizzy drive dogs... because I can!:lol: |
|
| Author: | GT1360 [ Fri Sep 30, 2005 9:20 pm ] |
| Post subject: | |
|
|
| Page 1 of 3 | All times are UTC + 10 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|