ausmini https://www.ausmini.com/forums/ |
|
gafmo strick's again https://www.ausmini.com/forums/viewtopic.php?f=2&t=1371 |
Page 1 of 1 |
Author: | min13k [ Sat Jul 31, 2004 7:46 pm ] |
Post subject: | gafmo strick's again |
well today we went up to gosford to kazjims cave sorta like alladins cave of precious gems and gold but this was a cave of preciouse mini parts but hang on i'm getting ahead of my self here ok we meet at the begining of the freeway at horsnby of we go up the freeway get off at gosford and head to nearest servo to get directions sweet find the street in the street directory of we go again get to the street and i stop and wave gaf up beside me what number i sez he looks at me dumbly then he looks for his little book with the addy in it um i've lost it oh ........ guess we best go find it he sez ok so we go back he nearly goes the wrong way on occasion ok walk in get the book goback pick my car up drive down the street and there is a mini in the drive ..... JIM SHE CANNAY TAKE ANY MORE ![]() but now to the goodies ![]() cooper mk2 head 850 hood linings door handle 2x g/b grill grill moustach 3 original bmc parts books door mech remote extension housing and a half roll cage plus i think there were some other bits but i dontreallyrememberi was like a kid in a toy shop i did not know which way to turn next tottal 450 ![]() and a upset wife for blowwing the budget ![]() ![]() makka |
Author: | 68matic [ Sun Aug 01, 2004 2:22 am ] |
Post subject: | |
can you explain the diff between a normal head and a cooper head and what is the budget for a happy wife? |
Author: | drmini in aust [ Sun Aug 01, 2004 7:19 am ] |
Post subject: | |
The head he got is a 12G940 MK2 S head. Same casting as a Morris 1100S head except S one has bigger inlet valves and 2 extra head stud holes. He's lucky he got it- If I'd seen it there last week I would have beat him to it... ![]() Oh well, I got an LS head instead, but it needs exhaust inserts- Makka's S one looks mint. ![]() |
Author: | Anto [ Sun Aug 01, 2004 10:57 am ] |
Post subject: | |
Mmmmm I'd like a 940 head strapped to the top of my motor. Unfortunately pocketing the block is too much effort - better off porting a 202 and sticking some 295 inlet valves in.... I have heard of somebody who pocketed their block in the car, with the pistons still in no less! I believe he cut round pieces of cardboard and put some silastic to seal. I believe the engine only lasted about a year after that then broke, for some inexplicable reason ![]() Anto. |
Author: | drmini in aust [ Sun Aug 01, 2004 11:44 am ] |
Post subject: | |
I did mine in the car back in '68... used Vegemite jar lid to protect the Imp pistons. Took a few hours careful work. 1275 gasket and good to GO. It blew away S's... ![]() You don't need a head with big MK2 S inlets valves for a 1098- an 1100S or Mini LS one is fine. ![]() |
Author: | gafmo [ Sun Aug 01, 2004 9:39 pm ] |
Post subject: | |
Greetings People's My List. Two 1128 Gearboxs (sand/dirt Included) - Morris Two 4 Point Cams Aproved Racing Harnises. - Marcia Twin metal Airhorns and Metal pump - Marcia Two Mini Van Rear lights complete - Marcia Front indercator glass (now Complete Set) Marcia Morris Rear Badge - Morris Remote Tunnel - Morris Two Remote gear sticks one Chromed - Morris Windscreen vent - Marcia Steering wheel suround - Marcia And new freinds Makka got the Best gril and suround - Dam ![]() Kazjim and family/Extended I dont think we miss one of the family on the front lawn after Makka and miy 3 Hours of Open eyed scround in Jim's 2nd Garage. If you have a chance checkout Kazjim's under budget turbo....NIce ![]() Additional today. After the night out with Sue's family and a number of saw heads. 1pm cam around and a chance to have a play on Marcia. Time to jack the back end up and pull it apart. Good Cylinders and Wheel bearing seam to be do resently(but may change anyway. Pax side uneven wear on pads and Cooper 's spacer drums. Driver side Groved same drums ![]() ![]() ![]() Thursday I also Purchase my Ujustable Tie Rods, Full Ajustable Rose Joint Bottom Arms and Camber brackets for the rear ![]() ![]() 1275 A+ Metro still arriving Thats me fpor now but real happy to have started with Marcia ![]() |
Author: | J_A_M [ Sun Aug 01, 2004 9:53 pm ] |
Post subject: | |
nice score Jim. Good to see someone with cash to flash..... ![]() |
Author: | drmini in aust [ Sun Aug 01, 2004 9:57 pm ] |
Post subject: | |
Between Gareth_1330, Makka and Gafmo, brother kazjim must be just about fresh out of Mini-K gearboxes by now.. ![]() |
Author: | Anto [ Sun Aug 01, 2004 10:03 pm ] |
Post subject: | |
gafmo wrote: Two 4 Point Cams Aproved Racing Harnises. - Marcia
I am very envious! I want a racing harness for my Mini, but unfortunately my racing seat doesn't have harness holes. I wondering whether a competant motor trimmer could add them for me... Anto. |
Author: | min13k [ Sun Aug 01, 2004 10:04 pm ] |
Post subject: | |
yup unless he has a secreet stash ![]() and if he do i will be there makka |
Author: | 68matic [ Sun Aug 01, 2004 11:13 pm ] |
Post subject: | |
makka can you explain the title of this thread "get-a-feckin-move-on strick again" or did i get gafmo from a wrong resource |
Author: | min13k [ Sun Aug 01, 2004 11:17 pm ] |
Post subject: | |
supoused to be strike's again but my damn illitercy jumped in again makka |
Author: | gafmo [ Mon Aug 02, 2004 8:37 am ] |
Post subject: | |
68Matic..Gafmo - You are correct |
Page 1 of 1 | All times are UTC + 10 hours |
Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |