| ausmini https://www.ausmini.com/forums/ |
|
| question about my SU https://www.ausmini.com/forums/viewtopic.php?f=2&t=13725 |
Page 1 of 1 |
| Author: | VeG [ Mon Dec 05, 2005 10:54 am ] |
| Post subject: | question about my SU |
Found a spare 1 1/2in SU in my shed, looks like its in good nick but in gonna rebuild it anyway. On the SU on my mini at the moment, there is 1 pipe on the float-chamber lid (where the fuel line goes). On the SU i found however, there seems to be 2 places to connect my fuel line on the float-chamber lid. So my question is - Do i change the float-chamber lid so i only have one pipe? Or do i just plug the other one up somehow? Or can i leave it as is? help appreciated 
|
|
| Author: | Mike_Byron [ Mon Dec 05, 2005 11:23 am ] |
| Post subject: | |
The two pipe ones are essentially to feed a second carby or a fuel return line. Either way you dont want it - change it to a single pipe type. There are couple of different types of float valves on the under side of the float valve cover. If your going to reco the carby anyway be sure to fit another (new) float valve. As well as a new gasket |
|
| Author: | VeG [ Mon Dec 05, 2005 11:31 am ] |
| Post subject: | |
ahhh, makes sense. Cheers 4 the help! |
|
| Author: | Sedona [ Mon Dec 05, 2005 11:54 am ] |
| Post subject: | |
If your not going to use the float chamber lid with two outlets, did you wanna part with it? 
Am in the middle of seeing if I can set up two LH bowl 1 1/2" SU's as twin carbs but need a twin outlet float lid........ |
|
| Author: | VeG [ Mon Dec 05, 2005 11:59 am ] |
| Post subject: | |
PM me with ur details, i guess id be willing to part with it. |
|
| Author: | Morris 1100 [ Mon Dec 05, 2005 7:02 pm ] |
| Post subject: | |
Ummmm...... Before you do anything, Are the two pipes next to each other? (One will be at a 45? angle to the other) Or, Is one pipe below the other? If it is the first one, it is to feed fuel to the second carby. If it is the second one, it is the float bowl vent and it has a hose to the charcoal cannister (or somewhere else) |
|
| Author: | VeG [ Mon Dec 05, 2005 11:47 pm ] |
| Post subject: | |
ahha, seems its the second. sorry sedona, u might be outta luck for now  PM sent.
with regards to the charcoal canister, can i get a hold of one separately or should i just change to a single float lid? |
|
| Author: | Morris 1100 [ Tue Dec 06, 2005 8:44 pm ] |
| Post subject: | |
VeG wrote: with regards to the charcoal canister, can i get a hold of one separately or should i just change to a single float lid?
Just turn the lid over and check underneath to make sure that I am right (or wrong) the lower pipe should just go straight under the lid and the top pipe should go to the needle valve. Don't worry about a cannister, just leave it alone and don't hook anything to it. |
|
| Author: | VeG [ Tue Dec 06, 2005 11:50 pm ] |
| Post subject: | |
yea had a look morris, looks like ur right. |
|
| Page 1 of 1 | All times are UTC + 10 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|