Ausmini
It is currently Fri Jul 18, 2025 3:27 pm

Board index » Mini Chat » Mini Chat

All times are UTC + 10 hours




Post new topic Reply to topic  Page 1 of 1
  [ 10 posts ] 
  Print view Previous topic | Next topic 
Author Message
_666_
 Post subject: Exhaust Anoyance...
PostPosted: Sat Jun 03, 2006 2:09 pm 
Offline
Die Die Die!!
User avatar

Joined: Sun Feb 12, 2006 6:29 pm
Posts: 2728
Location: Ad Delayed
ok where my exhaust meet the manifold there is a clamp holding it on... well that seal keeps going... and its giving me the shits... any cheap solutions ?
Top
 Profile  
 
stuvz
 Post subject:
PostPosted: Sat Jun 03, 2006 3:24 pm 
Offline
848cc
848cc
User avatar

Joined: Sun Jul 24, 2005 11:45 pm
Posts: 359
Location: Maitland.
isnt there sum type of tape u can put on this? (not masking tape :wink: ) sorry if im wrong
Top
 Profile  
 
drmini in aust
 Post subject:
PostPosted: Sat Jun 03, 2006 3:34 pm 
Offline
religious status
religious status
User avatar

Joined: Fri Mar 19, 2004 6:19 pm
Posts: 39754
Location: near Baulkham Hills, NSW
If standard Mini there is no seal there, it's just a tapered flange.
It takes a beating in rodchange cars (and 850s) because the exhaust pipe does much of the engine steadying.
The flange of the pipe may be cracked. A repair section of pipe is/was available to fix this.
There are 2 types of clamp- the bent tin one and the cast and machined type. Cast one is better if you can find one.

_________________
DrMini- 1970 wasaMatic 1360, Mk1S crank, 86.6HP (ATW) =~125 @ crank, 45 Dellorto (38 chokes), RE282 sprint cam, 1.5 rockers, 11.0:1 C/R. :mrgreen:
Top
 Profile  
 
_666_
 Post subject:
PostPosted: Sat Jun 03, 2006 3:41 pm 
Offline
Die Die Die!!
User avatar

Joined: Sun Feb 12, 2006 6:29 pm
Posts: 2728
Location: Ad Delayed
yeah its kinda tapered theny ou have the clamp to hold them together... works for awhile (i use silicone crap in there) and then it eventually starts leaking.. 74 clubman were talking bout here...
Top
 Profile  
 
drmini in aust
 Post subject:
PostPosted: Sat Jun 03, 2006 5:07 pm 
Offline
religious status
religious status
User avatar

Joined: Fri Mar 19, 2004 6:19 pm
Posts: 39754
Location: near Baulkham Hills, NSW
If it's been leaking bad for a while you will need a new clamp AND an exhaust pipe or the repair bit.

_________________
DrMini- 1970 wasaMatic 1360, Mk1S crank, 86.6HP (ATW) =~125 @ crank, 45 Dellorto (38 chokes), RE282 sprint cam, 1.5 rockers, 11.0:1 C/R. :mrgreen:
Top
 Profile  
 
_666_
 Post subject:
PostPosted: Sat Jun 03, 2006 5:16 pm 
Offline
Die Die Die!!
User avatar

Joined: Sun Feb 12, 2006 6:29 pm
Posts: 2728
Location: Ad Delayed
hmm ok... new exhaust pipe bit it is.. how come a new clamp as well ? clamp seems alright just dirty...
Top
 Profile  
 
drmini in aust
 Post subject:
PostPosted: Sat Jun 03, 2006 5:19 pm 
Offline
religious status
religious status
User avatar

Joined: Fri Mar 19, 2004 6:19 pm
Posts: 39754
Location: near Baulkham Hills, NSW
If it's the cast type clean it up, if the sheet metal type though, they are often bent.
These things get red hot down there on a long run. :wink:

_________________
DrMini- 1970 wasaMatic 1360, Mk1S crank, 86.6HP (ATW) =~125 @ crank, 45 Dellorto (38 chokes), RE282 sprint cam, 1.5 rockers, 11.0:1 C/R. :mrgreen:
Top
 Profile  
 
simon k
 Post subject:
PostPosted: Sat Jun 03, 2006 5:58 pm 
Offline
Yay For Hay!
User avatar

Joined: Wed Sep 08, 2004 9:27 pm
Posts: 15912
Location: Wodonga - Vic/NSW border
probably worth changing the top engine steady rubbers too - they are there to stop the engine rocking around and putting the engine steady load on the exhaust..... root cause ;)

_________________
did I tell you that I won a trophy?
Top
 Profile  
 
_666_
 Post subject:
PostPosted: Sat Jun 03, 2006 6:27 pm 
Offline
Die Die Die!!
User avatar

Joined: Sun Feb 12, 2006 6:29 pm
Posts: 2728
Location: Ad Delayed
skssng i think your onto something there.... and i beleive theyre cast...they dont seem flimsy enough to be steel...
Top
 Profile  
 
Jules
 Post subject:
PostPosted: Sat Jun 03, 2006 9:57 pm 
Offline
848cc
848cc

Joined: Mon Jun 20, 2005 7:04 am
Posts: 161
Location: SE Qld
You'll also be better off using exhaust cement in there instead of silicone (too hot for silicone).
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 10 posts ] 

Board index » Mini Chat » Mini Chat

All times are UTC + 10 hours


Who is online

Users browsing this forum: No registered users and 91 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  

© 2016 Ausmini. All garage work involves equal measures of enthusiasm, ingenuity and a fair degree of irresponsibility.