ausmini
https://www.ausmini.com/forums/

Come here to answer my stupid question..... Please!
https://www.ausmini.com/forums/viewtopic.php?f=2&t=22614		 Page 1 of 1
Author:  YoungMiniac [ Sat Sep 16, 2006 6:45 pm ]
Post subject:  Come here to answer my stupid question..... Please!
Now before you all laugh I must tell you I have no mechanic sense :P

Could anyone tell me what the big pipe, comming from head is on my engine and why it's there....

Image

Thanks all Ian :D

I SAID DON'T LAUGH!
Author:  YoungMiniac [ Sat Sep 16, 2006 6:46 pm ]
Post subject: 
And yes it all needs a clean and coat of paint... on to do list :D
Author:  gafmo [ Sat Sep 16, 2006 6:50 pm ]
Post subject: 
if it the pipe the has the four additional pipes connected and going into the head its part of the pollution gear....Laugh nar not from me :lol:
Author:  awdmoke [ Sat Sep 16, 2006 6:54 pm ]
Post subject: 
Yep, anti polution crap. You have the "smog head".
(an air compressor driven by the fan belt forced extra air to completely burn the hot exhaust gases)
Author:  YoungMiniac [ Sat Sep 16, 2006 6:54 pm ]
Post subject: 
gafmo wrote:
if it the pipe the has the four additional pipes connected and going into the head its part of the pollution gear....Laugh nar not from me :lol:


O thought so :P The lovely pollution gear that does nothing:?: :?: :?: :?: :P
Author:  Gadgets mini [ Sat Sep 16, 2006 7:23 pm ]
Post subject: 
just plumb your Nitrus into it it will inject it right to where its needed :wink: :wink:


VVTIC :wink:
Author:  AcTioN [ Sat Sep 16, 2006 7:29 pm ]
Post subject: 
:twisted:
Author:  simon k [ Sat Sep 16, 2006 11:05 pm ]
Post subject: 
Gadgets mini wrote:
just plumb your Nitrus into it it will inject it right to where its needed :wink: :wink:


VVTIC :wink:


que?? straight into the exhaust... :? :wink:
Author:  Morris 1100 [ Sat Sep 16, 2006 11:08 pm ]
Post subject: 
You know, to get a flame out the pipe. :twisted:
Author:  simon k [ Sat Sep 16, 2006 11:14 pm ]
Post subject: 
ahhh - afterburner.... very clever....
Author:  Mick [ Sun Sep 17, 2006 12:29 am ]
Post subject: 
you can rip it off if you want to clear the space out. you will just need to plug the holes with replacement plugs..
Author:  Blokeinamoke [ Sun Sep 17, 2006 8:10 am ]
Post subject: 
Yuo can put some holes in it and play it like a flute
Author:  simon k [ Sun Sep 17, 2006 10:13 am ]
Post subject: 
Mick wrote:
you can rip it off if you want to clear the space out. you will just need to plug the holes with replacement plugs..


or just bend the ends of the tubes over.... I've seen it work :shock:
Author:  Mick [ Sun Sep 17, 2006 10:54 am ]
Post subject: 
skssgn wrote:
or just bend the ends of the tubes over.... I've seen it work :shock:


Uh huh, you simply cut them off half an inch from the head with a pair of sidecutters and use pliers to ftatten the remaining tube. Works well, but you slice your hand open when you work on the engine cos the pieces of remaining pipe are sharp edged.

Mind you they're not doing any harm as is, they're just in the way..
Author:  Al Munday [ Sun Sep 17, 2006 11:15 am ]
Post subject: 
You can plug 'em off with a 7/16" unf bolt, loctite it and cut 'em off. Same thread as main stud. i think those heads all have hard exhaust seats too ! Good for unleaded fuel!
Page 1 of 1 All times are UTC + 10 hours
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/