| ausmini https://www.ausmini.com/forums/ |
|
| Doc's correct https://www.ausmini.com/forums/viewtopic.php?f=2&t=3127 |
Page 1 of 2 |
| Author: | gafmo [ Mon Nov 29, 2004 10:07 am ] |
| Post subject: | Doc's correct |
Doc came over yesturday arvo after a cry for help Morris would not start. I checked all the normals and doc did the thumb presure test..three and four ver little pressure, head gasket gone.. 
Just taken the head off and you can guess it.. both 3 and 4 piston are wet and a nice piece of gasket is missing. Look like Sue's without Morris for a little bit again  she's not happy
|
|
| Author: | J_A_M [ Mon Nov 29, 2004 10:40 am ] |
| Post subject: | |
well pull your finger out then Jim....nothing worse than a wife who is unhappy..... 
|
|
| Author: | gafmo [ Mon Nov 29, 2004 10:44 am ] |
| Post subject: | |
I have...Doc and I just need to do some work on the head to correct it..It may not be flat ? and I know what you mean about the wife..not forgetting Sue's a redhead
|
|
| Author: | J_A_M [ Mon Nov 29, 2004 10:46 am ] |
| Post subject: | |
gafmo wrote: .....not forgetting Sue's a redhead
|
|
| Author: | gafmo [ Mon Nov 29, 2004 11:12 am ] |
| Post subject: | |
Never you just have to know how to play them but i'm always learning 
|
|
| Author: | J_A_M [ Mon Nov 29, 2004 11:28 am ] |
| Post subject: | |
us married blokes never stop learning...that's my theory on marraige....because women are never wrong...apparently 
|
|
| Author: | gafmo [ Mon Nov 29, 2004 11:30 am ] |
| Post subject: | |
Thats what they all tell me....are they correct 
|
|
| Author: | drmini in aust [ Mon Nov 29, 2004 11:31 am ] |
| Post subject: | |
This time, we'll use a different gasket- NOT a copper one. They don't make them like they used to.
|
|
| Author: | gafmo [ Mon Nov 29, 2004 11:36 am ] |
| Post subject: | |
I'm still going to need an manifold and heater tap gaskets which I'll get a few other things sent to me at the same time..
|
|
| Author: | poeee [ Mon Nov 29, 2004 1:07 pm ] |
| Post subject: | |
Get a metal ruler out and check if it's flat. |
|
| Author: | willy [ Mon Nov 29, 2004 1:43 pm ] |
| Post subject: | |
 Get it fixed, gaf!
|
|
| Author: | gafmo [ Mon Nov 29, 2004 4:03 pm ] |
| Post subject: | |
Doc and I had some fun with the Doc's new Mill 
I'll put a picture up of the gasket in a sec |
|
| Author: | gafmo [ Mon Nov 29, 2004 4:13 pm ] |
| Post subject: | |
number 3 and 4 has a good size gap 1 and 2 is a little bit harder to see but it was going also 
Worked out what the problem was...Haynes book of lies say to do them up 40...I should have done them 50 leason learnt |
|
| Author: | aaron [ Mon Nov 29, 2004 4:53 pm ] |
| Post subject: | |
go a metro turbo gasket. shouldn't have the problem then |
|
| Author: | gafmo [ Mon Nov 29, 2004 5:23 pm ] |
| Post subject: | |
Its an 1100 not a 1275 |
|
| Page 1 of 2 | All times are UTC + 10 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|