hey all

i know this topic has been spoken about before but i couldnt find it


i was just wondering if i could get some tips on installing bucket seats in my mini


many thankz
danny

_________________

Yep no worries.

1. Make sure you put the drivers seat on the right side of the passengers seat.
If you dont then the driver will be on the left and that makes steering hard.
2. Have the seats facing forward. This way you can see where you're going.
3. Seatbelt goes over the seat, since its more comfortable to wear that way.
4. Seats are best held in with bolts. Glue is great but makes a mess on the carpet.

lol

no no
i know that part
lol
but i mean the railings lol


but thanks for them tips

_________________

I have the cobra type railings for my sparco seats.
They use the factory seat mounts, and two extra bolts through the floor.
They can be pricey to buy, but are the best and easiest for the job.

Do you have anything already?

i have the recaro seats and rails

but i dont know how im going to mount it so i can still be able to lift the seat up for people to get in the back seat

but i dont know if its possible :S


iv never seen them with my eyes before



so any ideas/ pictures would be great

_________________

No photos sorry.
My setup originally didn't have the two floor bolts at the rear.
So the seats flipped forward like normal. Since my seats are highbacks they barely went far enough to get anyone in, but they did.

haha ohh k
so its hard to get people in the back with high back buckets?

_________________

Well, in mine the seats were fixed back (no angle adjust) and the top of the seat hit the roof at about 20 degrees tilt.
I don't put passengers in the back of a mini anyway, so it was of no issue to me.

ohhhh
lol
i see i see


haha


but im still young and like to go out 4 drives


so yeh a full car is allways better then just 1 person
lol


unless its a female friend

_________________

I think your supposed to use a seat made for a two door car. Or else they don't flip forward and it is challenging to get into the back...

You could always just put a bucket seat in the drivers side and leave the passengers as it is...

post some pics of teh seats you have got.

i have sparcos in my race car, which i had a flat plate bent up to match bolt on the front crossmember, 2 bolts and seat is out, exactly the same design asd the original roundie seats.

in mad-mk1 i have reclining bucket seats, which i welded in another crossmember

cheers jamie

_________________
-jamie-
1963morris 850
1965 solid side van
1994 rover racecar

their recaro reclining bucket seats

il put some pics up this arvo

_________________

can i suggest you only put 1 bucket seat in and that the driver, im only putting one in, the missus can put up with sliding all over place because is isnt held in properly, and i can still get people in the back, its also the fact that even though i do trust my mates i dont trust their parrents and if i was to be in an accident and they get injured my fault or not because the seat is a modified fixture i will have the balls sued from me, where as i cant sue my self,

it would be good if we could do something like this legally: http://www.minifinity.com/modules.php?o ... at_fixings

_________________
any parts for a 76 clubby pm me or ring 0405 329 326

http://www.ausmini.com/forums/viewtopic.php?t=44717

plus this thread, http://www.ausmini.com/forums/viewtopic ... 3&start=15

_________________
any parts for a 76 clubby pm me or ring 0405 329 326

http://www.ausmini.com/forums/viewtopic.php?t=44717

We supply (and fit) Recaro's here at work.

This is the frame from our Work-Bus Triton.

You can see where the runners bolt into the 'tap rod' that runs the length of the seat, front-to-rear:



Seatbelt buckle mount:


Just get your heights and mounts right, then work up from there....

_________________
Cheap, Fast, Reliable. Choose two.