get a manual for 5 bucks and have a go your self... its very rewarding i assure you!
| ausmini https://www.ausmini.com/forums/ |
|
| anyone wanna help me change a head gasket? wollongong https://www.ausmini.com/forums/viewtopic.php?f=2&t=53011 |
Page 1 of 2 |
| Author: | andbat [ Fri May 08, 2009 6:17 pm ] |
| Post subject: | anyone wanna help me change a head gasket? wollongong |
turns out molly head gasket is blown, water is leaking into cylinder #3 and maybe #1 as well. or maybe the it's more then i can afford and the head is cracked. either way wont know if until the head is off. so is anyone able to come round to mine and help take the head off on street, so i can have the head checked. and then maybe come back to help put it back on once i find out it is perfectly fine. or can i take molly round to some-ones place and take the head off, and leave molly there while the head gets checked. or shall i just admit defeat and take it to the mechanic? i'm just not learning anything from taking it to the mechanic... and more importantly, i can't really afford it. help |
|
| Author: | TUCK3r [ Fri May 08, 2009 8:01 pm ] |
| Post subject: | |
your more than welcome to come around my house and do it. i have all the tools and loads of time as i dont have a job. Cheers TUCK3R |
|
| Author: | mattsmadmini [ Fri May 08, 2009 8:34 pm ] |
| Post subject: | |
get a manual for 5 bucks and have a go your self... its very rewarding i assure you!
|
|
| Author: | TUCK3r [ Fri May 08, 2009 9:02 pm ] |
| Post subject: | |
i dont think he has the tools to do it but if some one could lend him the tools that would be a great help to him. |
|
| Author: | Mini Mad [ Sat May 09, 2009 12:35 am ] |
| Post subject: | |
It's not hard at all, just a basic socket set would do and borrow a torque wrench to tighten it back up. Someone can post a scanned pick of the correct way to retorque the head. |
|
| Author: | mattsmadmini [ Sat May 09, 2009 3:28 am ] |
| Post subject: | |
40pounds torque.... |
|
| Author: | i got a mini [ Sat May 09, 2009 6:39 am ] |
| Post subject: | |
hey mate me and my bro just did one a few weeks ago easy as anything we just borrowed a torque wrench from a mate easy as it really easy |
|
| Author: | andbat [ Wed May 13, 2009 1:38 pm ] |
| Post subject: | |
okay gonna be doing it myself in the out on the street. any tips to keep block from rusting or removing head studs? what size buts do i need? if you were removing a cylinder head in the street what would you be looking out for and doing? also anyone know where i can get a cylinder head crack and pressure tested in wollongong? and would is be the better thing to do to have it shaved a bit? |
|
| Author: | ryan [ Wed May 13, 2009 1:54 pm ] |
| Post subject: | |
When are you planning on doing this? I may be able to come help. Martins engine recondition would be the best i think for getting the head done. Let me know, so I can make plans. |
|
| Author: | Mini Mad [ Wed May 13, 2009 2:01 pm ] |
| Post subject: | |
Hurry up and get it done for the two cruises coming up 
|
|
| Author: | andbat [ Wed May 13, 2009 2:06 pm ] |
| Post subject: | |
damn straight mini mad ryan i'm not doing anything these days so any asap day that suits you is best. |
|
| Author: | ryan [ Wed May 13, 2009 2:11 pm ] |
| Post subject: | |
No uni? I'm free all day tomorrow, so I can come around. I have never done one before, but I'm sure it can't be too hard. Tucker, do you want to come around as well? I don't have any mobile credit, so I wont be able to respond to any messages, so pm on here if we are going ahead with this. Ryan |
|
| Author: | andbat [ Wed May 13, 2009 8:20 pm ] |
| Post subject: | |
well i first need the replacement studs and head gasket. and i'm unsure if i can just show up to a shop with the head and they'll give it a shave. but i hope i can. so if we can do this all in one day it'd be cool. tucker do you reckon you'd be able to make the trip? with the parts and i'll pay you back? can't do it tomorrow actually, seeing the doc. |
|
| Author: | TUCK3r [ Wed May 13, 2009 8:25 pm ] |
| Post subject: | |
i know mini king has all the parts for what you need. if you want i am free for the next two days so you's are more than welcome to do it at my house. i have all tools and ryan could give you a lift back home if you had to wait for head maching. i would come down but hardly have any cash as im unemployed and trying to built a engine on limited funds myself. Cheers TUCK3R |
|
| Author: | andbat [ Wed May 13, 2009 8:39 pm ] |
| Post subject: | |
sounds reasonable. you up for it ryan? firstly we'd have to get molly started though. not impossible. so friday good for people? |
|
| Page 1 of 2 | All times are UTC + 10 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|