ausmini
https://www.ausmini.com/forums/

Vinyl Welding
https://www.ausmini.com/forums/viewtopic.php?f=2&t=7287		 Page 1 of 1
Author:  Mike [ Tue May 17, 2005 12:15 pm ]
Post subject:  Vinyl Welding
Hey I remember somebody talking about places in Sydney that do vinyl welding - you know like the original Morris interior seats and door cards. I'm missing a single RH front door card and its pissing me off so gonna have to get one done up. Anyone knows of places that do that?.
Author:  cush [ Tue May 17, 2005 12:31 pm ]
Post subject: 
you try a search?


i've got a set of exterior seats if you're bored with the interior ones... ;)
Author:  Metalfab_101 [ Tue May 17, 2005 1:13 pm ]
Post subject: 
MC_Cush wrote:
i've got a set of exterior seats if you're bored with the interior ones... ;)


Dude! are you doing kits? eg. complete with roof bracing and steering shaft extension??? :P
Author:  cush [ Tue May 17, 2005 2:20 pm ]
Post subject: 
you know it

Image

:)


hehe.. in looking for that.. i found this..

Image


sweeeet
Author:  dr trim [ Tue May 17, 2005 5:18 pm ]
Post subject: 
i do vinyl welding at tradeschool.

some of the trimmers around the place come there to do it. saying that im not to sure how many machines are left around the place :?
Author:  Mick [ Tue May 17, 2005 5:28 pm ]
Post subject: 
There's a place in inner south west sydney called Polyweld.
They will do a complete set of door cards for (better sit down for this) 400 dollars.

He has the machine doovie to make the lines.

When I spoke to him some weeks ago, he said that would be the price, but it would still take 4 to 6 weeks for him to get around to making them.
Author:  drmini in aust [ Tue May 17, 2005 7:39 pm ]
Post subject: 
There was a trim place at Granville (near the railway level crossing) that used to do it, I know where it is/was but can't remember their name. Top end stuff they did, so probably not cheap.
I'd like get some door cards stitched, like Chong did.. gotta twist his arm when I see him... :wink:
Author:  68matic [ Tue May 17, 2005 8:21 pm ]
Post subject: 
drmini in aust wrote:
I'd like get some door cards stitched, like Chong did.. gotta twist his arm when I see him... :wink:


his mum did that for him
Marcello wants my mum and her sweatshop skills to do his door cards too...

these asian immigrants... i knew we had a use for them :lol:
im sure we could pay them a fraction of that $400 too, like $2.37c

oh that was harsh... sorry mum :oops:
Author:  drmini in aust [ Tue May 17, 2005 8:35 pm ]
Post subject: 
68matic wrote:
drmini in aust wrote:
I'd like get some door cards stitched, like Chong did.. gotta twist his arm when I see him... :wink:


his mum did that for him
Marcello wants my mum and her sweatshop skills to do his door cards too...

these asian immigrants... i knew we had a use for them :lol:
im sure we could pay them a fraction of that $400 too, like $2.37c

oh that was harsh... sorry mum :oops:

I WOULD PAY MONEY... 8) :lol:
Author:  68matic [ Tue May 17, 2005 8:37 pm ]
Post subject: 
yeh $2.45 would cover it
:wink:
Author:  red078 [ Tue May 17, 2005 8:58 pm ]
Post subject: 
G'day everyone, has anyone ever had cracks on their dash tops plastic welded?, if so is it very successful. Tony :D
Author:  drmini in aust [ Tue May 17, 2005 9:33 pm ]
Post subject: 
red078 wrote:
G'day everyone, has anyone ever had cracks on their dash tops plastic welded?, if so is it very successful. Tony :D

Yep I got my Fiat 124S done 20? years ago, they reskinned it. Looked good and lasted. Cost me $115 back then. :wink:
Author:  Mike [ Wed May 18, 2005 1:53 am ]
Post subject: 
Yea called Pollyweld - $400 bux or $100 for a single card. There's another place at Botany which is a closer to me and they quoted me $100 too so I might try them.
Author:  czerial [ Wed May 18, 2005 11:27 am ]
Post subject: 
I used polyweld for my door cards. they were $400. came out great!

Image

Image
Page 1 of 1 All times are UTC + 10 hours
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/