You need a ball joint remover, some people use hammers but after you have used this tool you wont try with a hammer again.
Here is a link
http://www.supercheapauto.com.au/online ... escription
Good luck
| ausmini https://www.ausmini.com/forums/ |
|
| front suspension probs https://www.ausmini.com/forums/viewtopic.php?f=2&t=75682 |
Page 1 of 1 |
| Author: | LAZZA1964 [ Sat Feb 25, 2012 5:25 pm ] |
| Post subject: | front suspension probs |
can anyone help me tried almost al day to remove front suspension to no avail could not remove tie rod ends from steering arm do you need a special tool to do these also upper and lower swivel joints is this also another special tool and also tie bar from from swivel joints are theses all brut strength or both tool and strength also removal of steering arm was a no go can someone give ume a clue . novice !!!!!! |
|
| Author: | 123grosso [ Sat Feb 25, 2012 5:50 pm ] |
| Post subject: | |
You need a ball joint remover, some people use hammers but after you have used this tool you wont try with a hammer again. Here is a link http://www.supercheapauto.com.au/online ... escription
Good luck |
|
| Author: | simon k [ Sat Feb 25, 2012 8:16 pm ] |
| Post subject: | |
123grosso wrote: You need a ball joint remover, some people use hammers but after you have used this tool you wont try with a hammer again.
Here is a link http://www.supercheapauto.com.au/online ... escription Good luck that's the one to use - I bought the same one from supercheap and it works fine, but I'm sure it was less than half that price 
make sure you grease the thread! |
|
| Author: | LAZZA1964 [ Sun Feb 26, 2012 9:34 am ] |
| Post subject: | suspension probs |
ok to you guys that replied to my probs i would like to say thank you very much the info and link was very much appreciated ... laz |
|
| Author: | DA9jeff [ Sun Feb 26, 2012 11:40 am ] |
| Post subject: | |
^^^ Supercheap have a habit of raising prices at "Sale" time....people still think they are getting a bargain. 
|
|
| Author: | Morris 1100 [ Sun Feb 26, 2012 12:18 pm ] |
| Post subject: | |
I got one form Supercheap, undid one side Ok, tried the other side and broke the tool. Back to the trusty hammer. |
|
| Author: | PDJ [ Sun Feb 26, 2012 1:40 pm ] |
| Post subject: | |
I had a Supercheap one and it worked great for me. Lent it to a member on here who banjoed it first go  
|
|
| Author: | michaelb [ Sun Feb 26, 2012 5:30 pm ] |
| Post subject: | |
I think most of the auto shops sell these tools? I got mine from Auto one and it's still going strong But in the past I have had to cut and drill out a top ball joint which refused to let go |
|
| Author: | adamstuart [ Sun Feb 26, 2012 7:17 pm ] |
| Post subject: | |
Morris 1100 wrote: I got one form Supercheap, undid one side Ok, tried the other side and broke the tool.
Back to the trusty hammer. This sounds familiar! |
|
| Author: | adamstuart [ Sun Feb 26, 2012 7:18 pm ] |
| Post subject: | |
PDJ wrote: I had a Supercheap one and it worked great for me.
Lent it to a member on here who banjoed it first go Hey so does this! 
|
|
| Page 1 of 1 | All times are UTC + 10 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|