ausmini
https://www.ausmini.com/forums/

newton commercial interiors
https://www.ausmini.com/forums/viewtopic.php?f=2&t=81128		 Page 1 of 1
Author:  mad-mk1 [ Thu Apr 18, 2013 1:57 pm ]
Post subject:  newton commercial interiors
hey everyone i have recently bought a interior from newton commercial, awesome piece of kit. its lovely. however i picked the wrong doorcards, novice mistake.

does anyone know what the right ones are for wind up windows? i cant seem to find the right ones, not sure if its just me though.

cheers jamie
Author:  Harley [ Thu Apr 18, 2013 1:58 pm ]
Post subject: 
They didn't have aussie wind up window doors overseas, so there would be no market to make them.
Author:  mad-mk1 [ Thu Apr 18, 2013 2:00 pm ]
Post subject: 
Harley wrote:
They didn't have aussie wind up window doors overseas, so there would be no market to make them.


this could infact be my "derp" issue, no biggie i can make them fit :D
Author:  Harley [ Thu Apr 18, 2013 2:03 pm ]
Post subject: 
Making them fit is easy, making them look good is not.
What I'd do is request the kit, but only have them supply you with uncut door material that you can give to a trimmer to put over old aussie cards.
Author:  mad-mk1 [ Thu Apr 18, 2013 2:06 pm ]
Post subject: 
Harley wrote:
Making them fit is easy, making them look good is not.
What I'd do is request the kit, but only have them supply you with uncut door material that you can give to a trimmer to put over old aussie cards.


tad late for that, unless i re order. ill have a look and speak to my trimmer and see what the best plan of attack is! i have a couple ideas! remind me this when i want trim for the van harlski!
Author:  66S [ Thu Apr 18, 2013 2:11 pm ]
Post subject: 
Jamie, have you asked Newtons if they can do a set? It wouldn't surprise me if they could. South African Minis used the same doors and I know that there are both them and Aussie ones in the UK.

Al
Author:  Harley [ Thu Apr 18, 2013 2:15 pm ]
Post subject: 
mad-mk1 wrote:
[ i have a couple ideas! remind me this when i want trim for the van harlski!


No problems. We'll see about ditching those quarter windows too! :lol:
Author:  Babes [ Thu Apr 18, 2013 3:28 pm ]
Post subject: 
I bought my countryman interior from them custom made pattern on the seat covers and door cards.

The headlining was wrong, not enough sleeves for the roof bows. The seat covers were wrong, oval backs instead of a flat back. The door cards were wrong, fuel filler on the wrong side. All this despite sending them maybe 30 pictures of the interior to copy.

They did send me replacements for everything that was wrong though, must of been a Friday afternoon order :roll:
Author:  MattE [ Thu Apr 18, 2013 6:53 pm ]
Post subject: 
I emailed Lisa Moffat from Newtons a month or so ago, and she replied:

"We can produce the door panels requested for £56.47 a pair plus delivery of £60 DHL(unfortunately high price for the cost of the item but cannot get any cheaper)."

My question was:
"Hello,
A friend told me you now manufacture interior trim for the Australian
minis - specifically, the door trim for our windup window doors."

I later clarified for her by saying

"these ones have a door handle hole and
a window winder hole below it. Both about 1" holes.
It's a 1968 Australian Mini Deluxe, but in Australia all doors are the
same as these from about 1965 to 1971, so includes Cooper S."

They must have the templates now.

So definitely worth enquiring along these lines.

She asked for a photo, as she was keen to supply the correct trims.

Hope this helps.
Matt
PS - PM me if you would like me to forward the email exchange.
Author:  68Rusty [ Fri Apr 19, 2013 2:39 pm ]
Post subject: 
Hi all,
I purchased a Newton complete trim kit late last year. I rang up and spoke with Katie who was fantastic to deal with. She said straight off that they could do an Australan 1968 Deluxe but I sent a few photos any way to make sure.
She sent me a bunch of trim samples to choose from, the whole process went rather smoothly. Everything looks pretty good although I have not fitted yet, it all looks correct though.

I would give them a call and ask for Katie.

I will try to post some photos at some stage of the new trim kit.
Author:  Firefirey [ Fri Apr 19, 2013 7:27 pm ]
Post subject:  Newton trim
[quote="68Rusty"]Hi all,
I purchased a Newton complete trim kit late last year. I rang up and spoke with Katie who was fantastic to deal with. She said straight off that they could do an Australan 1968 Deluxe but I sent a few photos any way to make sure.
She sent me a bunch of trim samples to choose from, the whole process went rather smoothly. Everything looks pretty good although I have not fitted yet, it all looks correct though.

I would give them a call and ask for Katie.

I will try to post some photos at some stage of the new trim kit.[/quote]

Hi I was intouch with Johnny Newton a few weeks ago in regards to Aussie trim and they now make trim for mk 1 Aussie minis. He did say that it is not listed yet but will be soon. He also sent some photo's of there work for Aussie trim if any body wants to email I will forward the info.
I'm looking into getting a classic Mk 1 recliner seat done in Aussie trim for my cooper s.
Regards Pete.
Author:  brett [ Sat Apr 20, 2013 12:54 am ]
Post subject: 
I have a set of newton commercial aussie spec doors.. the fit perfectly. Also bear in mind that the colours and grain is totally different than Australian vinyl..
Author:  mad-mk1 [ Sun Apr 21, 2013 12:06 am ]
Post subject: 
Thanks for all your replies guys!
i do believe i can work out what to do, but if it fails i will definentally get back onto them and get a set for aussie doors! silly mistake on my behalf!

cheers
Page 1 of 1 All times are UTC + 10 hours
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/