LF Performance do great work,
http://www.lfperformance.com.au/
but it will cost you for something like this:
There's always the option of a Bond cage for the budget end of the market.
| ausmini https://www.ausmini.com/forums/ |
|
| Roll Cage Fabricators Perth WA https://www.ausmini.com/forums/viewtopic.php?f=2&t=81185 |
Page 1 of 1 |
| Author: | Citric [ Mon Apr 22, 2013 4:02 pm ] |
| Post subject: | Roll Cage Fabricators Perth WA |
Hi I am looking to get into some motor sport with my Mini, looking to Motorkhana eventually, for personal peace of mind and personal safty, I would like to fit a type 2, Roll Cage as specified in Schedule J of the CAM regulations. Would anyone have any recommendations as to who to see in WA? Cheers Adam |
|
| Author: | doogie [ Mon Apr 22, 2013 5:08 pm ] |
| Post subject: | |
You really don't need a roll cage for motorkhana's, only 1st gear is ever used, but each to their own, if you want a roll cage go for it, don't expect much change out of $4000. Doogie |
|
| Author: | Citric [ Mon Apr 22, 2013 5:21 pm ] |
| Post subject: | |
Thanks for the reply doogie, i am pretty sure i will be doing other events besides motorkhana, where i do get out of 1st gear, and i fully expect it to be expensive. I was hoping someone on here could give me a recommendation? |
|
| Author: | DA9jeff [ Thu Apr 25, 2013 12:44 pm ] |
| Post subject: | |
A full 6 point from Walker Chassis in Adelaide [ for an IPRA Race car to full Cams specs] cost $2400 ...& that was into a Honda Integra. He has Quoted $1500 for a Type 3 ROPS into the Mini...to Cams Specs . Pay more than $2000 for a Mini.... you are being ripped off. You have never seen a car roll in 1st gear at a Motorkhana, Doogie??? |
|
| Author: | Citric [ Mon Apr 29, 2013 4:45 pm ] |
| Post subject: | |
Thanks for the info DA9jeff I will keep Walker Chassis in mind. |
|
| Author: | awdmoke [ Mon Apr 29, 2013 5:18 pm ] |
| Post subject: | |
What about a Safety Devices cage? http://www.minisport.com/mini-spare-parts/info_SAFRBN005SRSBLK.html |
|
| Author: | awdmoke [ Mon Apr 29, 2013 5:57 pm ] |
| Post subject: | |
LF Performance do great work, http://www.lfperformance.com.au/ but it will cost you for something like this:
There's always the option of a Bond cage for the budget end of the market. |
|
| Author: | mini_mad_matt [ Mon Apr 29, 2013 6:20 pm ] |
| Post subject: | |
That looks like some serious overkill right there! |
|
| Author: | Monaco [ Mon Apr 29, 2013 6:41 pm ] |
| Post subject: | |
mini_mad_matt wrote: That looks like some serious overkill right there!
 Ditto! I am not sure if it will go fast enough to roll with the extra 1200kg of tube!
|
|
| Author: | Citric [ Tue Apr 30, 2013 7:25 pm ] |
| Post subject: | |
awdmoke wrote: What about a Safety Devices cage? http://www.minisport.com/mini-spare-parts/info_SAFRBN005SRSBLK.html Shipping might be a killer! awdmoke wrote: LF Performance do great work,
http://www.lfperformance.com.au/ There's always the option of a Bond cage for the budget end of the market. that might be a bit much, but the work look great! I will keep them in mind! thanks again. |
|
| Author: | GR [ Tue Apr 30, 2013 7:51 pm ] |
| Post subject: | |
Hi awdmoke I was told about your cage so i had a look, thats one serious roll over cage the v8 super guys would be proud of that, but i have one serious question where are you going to hook your rear seat belts up to? Graham Russell |
|
| Author: | mini_mad_matt [ Tue Apr 30, 2013 8:56 pm ] |
| Post subject: | |
Just loop them over the horizontal bar behind the seat? Or is the angle or distance wrong? |
|
| Author: | awdmoke [ Wed May 01, 2013 11:52 am ] |
| Post subject: | |
It's not mine. It belongs to Mica, one of the more serious racers over here. I'll have a look next time I see it. |
|
| Page 1 of 1 | All times are UTC + 10 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|