ausmini
https://www.ausmini.com/forums/

which Wheels to buy ?
https://www.ausmini.com/forums/viewtopic.php?f=2&t=81828		 Page 1 of 1
Author:  _666_ [ Tue Jun 18, 2013 10:14 pm ]
Post subject:  which Wheels to buy ?
ok i need your opinion, im trying to decide which wheels to buy for my moke

im looking at the 15x7/16x7 range, (im under the impression that they will fit without mods and are of the right PCD)

im planning to paint my moke this colour -

Image

option 1 15x7.5 - is the blue too much ? AUD$240
http://www.allwheels.com.au/product.php?productid=31213&cat=0&featured=Y

option 2 - 15x7.5 - [font=Verdana]AUD$240[/font]
[font=Verdana][size=78%]http://www.allwheels.com.au/product.php?productid=31211&cat=0&featured=Y[/size][/font]

option 3 - 15x7 - [color=rgb(201, 116, 119)][font=Garamond][/size][size=0.9em]£250[/size][/font][/color]
http://www.force-racing.co.uk/uploads/i ... 15-dsy.jpg
http://www.force-racing.co.uk/wheels-15/

Option 4 13x7
http://www.minispares-online.co.uk/?cat_id=202&sub_cat_id=208&prod_id=3246

option5 13x7
http://www.minispares-online.co.uk/?cat_id=202&sub_cat_id=208&prod_id=3265

option 6 13x7 - £78.55
http://www.midlandwheels.com/Shop/P-2834-7-x-13-JBW-Mamba-Black.html
Author:  _666_ [ Tue Jun 18, 2013 10:24 pm ]
Post subject: 
theres also these too

http://mach5wheels.co.uk/wheels/mach-5- ... stud#!/-1/
Author:  willy [ Tue Jun 18, 2013 10:47 pm ]
Post subject: 
a 7" wheel (pretty much no matter the offset, because they will come very close to the trailing arm) is going to stick out a fair way on a Moke with standard guards.

Good luck.
Author:  _666_ [ Tue Jun 18, 2013 11:42 pm ]
Post subject: 
How did you overcome it willy ? We're your modified ?
Author:  PDJ [ Wed Jun 19, 2013 7:39 pm ]
Post subject: 
Make sure the wheels are a 4 inch (101.4?) PCD and not a "make them fit" 100 PCD.
It may only be 1+a bit mm smaller but you'll be bending the studs and obviously that ain't good.
You might be able to get the wheels drilled to a 4 inch PCD :?
Author:  Ace Radster [ Wed Jun 19, 2013 8:06 pm ]
Post subject: 
I gave it a lot of thought and can't go past option 5
The chrome ones are too chrome, if that makes sense.
I couldn't blame you for going with option 1 or 3 either
Author:  meeni [ Thu Jun 20, 2013 9:43 am ]
Post subject: 
If you can afford them get the force racing wheels, mini lites are like a rse holes..

Be different, but not orange 4 spoke different
Author:  Davo [ Thu Jun 20, 2013 9:47 am ]
Post subject: 
Another vote for option 5
Author:  TheMiniMan [ Thu Jun 20, 2013 11:37 am ]
Post subject: 
option 3

Carls wheels are Da-Bomb
Author:  Panthersteve [ Thu Jun 20, 2013 11:56 am ]
Post subject: 
option 1

but I bet you will go for the ones you want, not which option gets the most votes :wink:
Author:  simon k [ Thu Jun 20, 2013 1:23 pm ]
Post subject: 
wait till you have a drivable car....
Author:  _666_ [ Thu Jun 20, 2013 1:27 pm ]
Post subject: 
Well apparently 7.5" width isn't going to under the guards too well, might go for 15x7
Author:  braad [ Thu Jun 20, 2013 2:21 pm ]
Post subject: 
Just widen the guards. Its just sheetmetal!

Carls wheels (force racing) are awesome. A++, would buy if had the money
Page 1 of 1 All times are UTC + 10 hours
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/