ausmini
https://www.ausmini.com/forums/

Should I stick it in?
https://www.ausmini.com/forums/viewtopic.php?f=2&t=83845		 Page 1 of 2
Author:  Wombat [ Fri Dec 13, 2013 2:27 pm ]
Post subject:  Should I stick it in?
Just got some new stepped drums with studs and screws - some of the studs are a loose fit and the splines don't bite. Should I Loctite or Araldite them in place?
Author:  peterb [ Fri Dec 13, 2013 2:35 pm ]
Post subject:  Re: Should I stick it in?
Replace hub.
Author:  Wombat [ Fri Dec 13, 2013 2:44 pm ]
Post subject:  Re: Should I stick it in?
Duh! My ultimate bad! :oops: Wasn't playing with the hub but the drum and thinking sh*t these are loose. Brain fade AGAIN!
Author:  Mick [ Fri Dec 13, 2013 2:57 pm ]
Post subject:  Re: Should I stick it in?
Lucky you didn't araldite them in then huh :lol:
Author:  Wombat [ Fri Dec 13, 2013 4:26 pm ]
Post subject:  Re: Should I stick it in?
Mick wrote:
Lucky you didn't araldite them in then huh :lol:


Then I would be asking how to dissolve araldite :lol:
Author:  Mick [ Fri Dec 13, 2013 4:32 pm ]
Post subject:  Re: Should I stick it in?
Then I would be telling you to use liquid nails...
Author:  frednutz&co [ Fri Dec 13, 2013 4:33 pm ]
Post subject:  Re: Should I stick it in?
araldite should only be used to stick crumbs on chicken when you microwave it :D














long funny story :evil: :evil:
Author:  winabbey [ Fri Dec 13, 2013 5:25 pm ]
Post subject:  Re: Should I stick it in?
David - send me a PM if you'd like this whole thread deleted so it can't be referenced in years to come. There's only so much ridicule a Mini enthusiast who's made a simple mistake should have to handle. :D
Author:  Wombat [ Fri Dec 13, 2013 6:12 pm ]
Post subject:  Re: Should I stick it in?
It's helping me laugh at myself !
Author:  John Smidt [ Fri Dec 13, 2013 6:58 pm ]
Post subject:  Re: Should I stick it in?
Wombat wrote:
Just got some new stepped drums with studs and screws - some of the studs are a loose fit and the splines don't bite. Should I Loctite or Araldite them in place?


I have some studs with a coarse spline on them if you like I will send You a set
if they work
it may save You a bit of money if they do not then send them back
if they work and the other studs are not damaged and I can sell them
then it will not cost you anything
best regards
John
Author:  junior [ Fri Dec 13, 2013 7:28 pm ]
Post subject:  Re: Should I stick it in?
John Smidt wrote:
Wombat wrote:

I have some studs with a coarse spline on them if you like I will send You a set
if they work
it may save You a bit of money if they do not then send them back
if they work and the other studs are not damaged and I can sell them
then it will not cost you anything
best regards
John


You won't get a better offer than that.

Generosity & the willingness of others prepared to help is what's makes this community great.
Author:  TK [ Fri Dec 13, 2013 7:36 pm ]
Post subject:  Re: Should I stick it in?
He was trying to fit the studs to the drum and not the hub!!!
Author:  frednutz&co [ Fri Dec 13, 2013 9:36 pm ]
Post subject:  Re: Should I stick it in?
its Friday and Christmas is coming we all have days like that sometimes :lol: :lol: :lol: :lol: :oops: :lol: :lol:
Author:  brett [ Sat Dec 14, 2013 12:09 am ]
Post subject:  Re: Should I stick it in?
what do you expect Friday the 13th
Author:  Wombat [ Sat Dec 14, 2013 6:17 am ]
Post subject:  Re: Should I stick it in?
I was a little excited - not simply for have something for the Mini turn up in the post but also solving a problem. The problem being a 7 year old grandson down from Rocky for Christmas who has asked to work on the Mini with Pa. Now I have a task for him that he can do almost unaided.
Page 1 of 2 All times are UTC + 10 hours
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/