I paid about $300 to get a set of new LCBs done last year. Well worth it if you hate the look of rusty exhaust manifolds
Done by HPC (High Performance Coatings) in Leongatha, Vic.
| ausmini https://www.ausmini.com/forums/ |
|
| JET HOT coating https://www.ausmini.com/forums/viewtopic.php?f=2&t=84889 |
Page 1 of 1 |
| Author: | Minimadmarty [ Thu Mar 13, 2014 11:16 am ] |
| Post subject: | JET HOT coating |
How much does it cost to get an extractor Jet Hot coated? |
|
| Author: | jb007 [ Thu Mar 13, 2014 3:32 pm ] |
| Post subject: | Re: JET HOT coating |
Minimadmarty wrote: How much does it cost to get an extractor Jet Hot coated? Looking here another user has had it done: http://www.ausmini.com/forums/viewtopic.php?f=5&t=1437&p=14777&hilit=jet+hot#p14777 Jim |
|
| Author: | Curly [ Thu Mar 13, 2014 3:59 pm ] |
| Post subject: | Re: JET HOT coating |
I paid about $300 to get a set of new LCBs done last year. Well worth it if you hate the look of rusty exhaust manifolds Done by HPC (High Performance Coatings) in Leongatha, Vic.
|
|
| Author: | Mr Orange [ Thu Mar 13, 2014 5:34 pm ] |
| Post subject: | Re: JET HOT coating |
HPC ceramic coated my LCBs for about $160. |
|
| Author: | MINImal effort [ Thu Mar 13, 2014 6:50 pm ] |
| Post subject: | Re: JET HOT coating |
I'm looking at HPC to do my new LCBs and inlet manifold. Last week got estimate of: $275 for the LCB in HP2 $55 weber inlet in HP1 (+ postage) |
|
| Author: | Minimadmarty [ Thu Mar 13, 2014 7:09 pm ] |
| Post subject: | Re: JET HOT coating |
Curly wrote: I paid about $300 to get a set of new LCBs done last year. Well worth it if you hate the look of rusty exhaust manifolds Cheers, that's the look I'm looking for and $300 isn't too bad. Just need to find somewhere in Perth to get it done 
|
|
| Author: | 1071 S [ Thu Mar 13, 2014 9:32 pm ] |
| Post subject: | Re: JET HOT coating |
From memory the quoted price included postage.... Why don't you go to their web site for a proper quote instead of guessing??? Ian |
|
| Author: | 1310/71 [ Fri Mar 14, 2014 7:19 am ] |
| Post subject: | Re: JET HOT coating |
I had a small non-mini related combined inlet/extractor setup coated by competition coatings in South Granville NSW and it was $250 so your quote seems in the ball park. Edit - Couldn't the pic to upload this morning, here is the ones I had done. 
|
|
| Author: | boomini [ Fri Mar 14, 2014 7:26 am ] |
| Post subject: | Re: JET HOT coating |
Is their any power gains to coating or is it just a looks thing amd to keep heat down? |
|
| Author: | MG Rocket [ Fri Mar 14, 2014 7:34 am ] |
| Post subject: | Re: JET HOT coating |
boomini wrote: Is their any power gains to coating or is it just a looks thing amd to keep heat down? The theory is that the gasses are kept hot therefore the speed of the gases are kept up.The power gains are made by not having the gasses loitering around in the ports and extractors. |
|
| Author: | Minimadmarty [ Fri Mar 14, 2014 8:25 am ] |
| Post subject: | Re: JET HOT coating |
boomini wrote: Is their any power gains to coating or is it just a looks thing amd to keep heat down? Mostly looks the website claims increase BHP (one or two percent), inhibits thermal fatigue and reduced engine temperature! Only small bonuses but still every little bit helps...... |
|
| Page 1 of 1 | All times are UTC + 10 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|