Im quite sure thats dearer than normal for hypatecs....
Wait for Kev to reply...he knows the prices
| ausmini https://www.ausmini.com/forums/ |
|
| Opinion - Ebay Piston Sets https://www.ausmini.com/forums/viewtopic.php?f=2&t=8611 |
Page 1 of 2 |
| Author: | Konzo [ Thu Jun 30, 2005 2:21 pm ] |
| Post subject: | Opinion - Ebay Piston Sets |
Hey all, Are these a good price? http://cgi.ebay.com.au/ws/eBayISAPI.dll?ViewItem&category=32072&item=4559343004&rd=1 http://cgi.ebay.com.au/ws/eBayISAPI.dll?ViewItem&category=32072&item=4559342929&rd=1 Lucas |
|
| Author: | MiniK [ Thu Jun 30, 2005 2:41 pm ] |
| Post subject: | |
Im quite sure thats dearer than normal for hypatecs.... Wait for Kev to reply...he knows the prices
|
|
| Author: | Konzo [ Thu Jun 30, 2005 2:42 pm ] |
| Post subject: | |
Okay ... they are ebay, so I thought they might have been a bit expensive 
Ill wait for kev |
|
| Author: | J_A_M [ Thu Jun 30, 2005 2:44 pm ] |
| Post subject: | |
I think that is cheap actually.... I just put them in JAM recently (not new though). |
|
| Author: | Lillee [ Thu Jun 30, 2005 3:23 pm ] |
| Post subject: | |
Hypatechs are around $300 a set... that's what Kev told me... 
|
|
| Author: | minicranks [ Thu Jun 30, 2005 3:26 pm ] |
| Post subject: | |
its a bit cheaper than im paying for them from Ken, but i must admit that is because i buy the bigger 73 and 73.5mm pistons and rings so i would say its still a good deal. |
|
| Author: | Lillee [ Thu Jun 30, 2005 3:46 pm ] |
| Post subject: | |
And don't forget this item has 6 days to go! |
|
| Author: | Konzo [ Thu Jun 30, 2005 3:52 pm ] |
| Post subject: | |
yeah 6 days ..... thats a long time on ebay
so people would agree that $300 would be a good price? |
|
| Author: | Minimic [ Thu Jun 30, 2005 4:01 pm ] |
| Post subject: | |
Look down further, he has two sets Buy it Now @ $175. |
|
| Author: | Lillee [ Thu Jun 30, 2005 4:24 pm ] |
| Post subject: | |
That is cheap I'd say |
|
| Author: | TK [ Thu Jun 30, 2005 5:46 pm ] |
| Post subject: | |
They are cheap!!! I paid $275 for my 020 for my group Nb race car. Yes they are a very good piston!!! |
|
| Author: | drmini in aust [ Thu Jun 30, 2005 7:13 pm ] |
| Post subject: | |
Yes that is cheap, I was quoted $250 a while back. As said 73.0mm ones (1360cc) are dearer (around $270-290), but Ken Nelson and Graham Russell do have them. Don't forget to add the postage... 
|
|
| Author: | MiniK [ Thu Jun 30, 2005 8:58 pm ] |
| Post subject: | |
id forgotten if it was 150 or 250 a set... I knew Kev knew the price
|
|
| Author: | CPOCSM [ Thu Jun 30, 2005 10:50 pm ] |
| Post subject: | |
Gday guys - was about to ask what kind of quality they were(hypertecs). Well I have bought one of the 2 sets of "Buy It Now" 30 thou over pistons. I was looking for 20 thou but 30 wont be too bad - still gives me 2 x overbores... Just have to get this motor together now when the slugs arrive and hand them over to QIM for the final bore and hone... Hooroo for now Rob Forsyth Miniot!! |
|
| Author: | minicranks [ Fri Jul 01, 2005 7:39 am ] |
| Post subject: | |
hypatecs are good pistons, have had no problems with the 11 sets i have used in the past for customers. It will give you more than 2 oversize bores you have atleast 4 over sizes you can do. I just wish i had the extra money to stock up on them now but cant leave money sitting on the shelf for too long. |
|
| Page 1 of 2 | All times are UTC + 10 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|