Get a wheel alignment.
The left wheel is the one that spins, keeping that in mind.
ALso, mine wears on the OUTSIDE first, indicating some positive camber... yeah me needs a wheel alignment too.
| ausmini https://www.ausmini.com/forums/ |
|
| Can someone tell me why my tire is wearing the way it is? https://www.ausmini.com/forums/viewtopic.php?f=2&t=8905 |
Page 1 of 2 |
| Author: | Mini Mad [ Fri Jul 08, 2005 5:55 pm ] |
| Post subject: | Can someone tell me why my tire is wearing the way it is? |
My tire's are indeed close to needing replacement, but i had it up on a hoist this afternoon getting some exhaust work done, and the front LH tire is bald on the inside, none of the other's are..all of them have more wear on the outside from cornering i guess, but it's only the inside of the front LH tire that seems odd.. any ideas? |
|
| Author: | willy [ Fri Jul 08, 2005 5:58 pm ] |
| Post subject: | |
Get a wheel alignment. The left wheel is the one that spins, keeping that in mind. ALso, mine wears on the OUTSIDE first, indicating some positive camber... yeah me needs a wheel alignment too.
|
|
| Author: | Mini Mad [ Fri Jul 08, 2005 6:04 pm ] |
| Post subject: | |
I forgot to mention i just had an alignment.. Is it alway's the left wheen that spins? cause that could be it  ...there's lots of spinning going on  I think both of them spin though...
|
|
| Author: | willy [ Fri Jul 08, 2005 6:08 pm ] |
| Post subject: | |
Nar most chances its just the left that spins. Check the marks in the driveway for evidence 
Yeah wheelspin is good stuff... cept when it comes to new tyre time
|
|
| Author: | Dylans Clubby [ Fri Jul 08, 2005 6:35 pm ] |
| Post subject: | |
oh so you guys have only 1 wheel spinning as well then? i though i had an error. not that i do it much anyway. only on grass and gravel  good boy
|
|
| Author: | willy [ Fri Jul 08, 2005 6:37 pm ] |
| Post subject: | |
It hits two wheels if you turn the wheels... but don't do it or you can say bye bye to your diff 
|
|
| Author: | Dylans Clubby [ Fri Jul 08, 2005 6:39 pm ] |
| Post subject: | |
speaking from experience are we will??????
|
|
| Author: | willy [ Fri Jul 08, 2005 6:40 pm ] |
| Post subject: | |
Not direct experience... mate has had it happen before tho
Shears teeth off the pinion and a lot of other nasty stuff 
|
|
| Author: | mini_van_1970 [ Fri Jul 08, 2005 7:12 pm ] |
| Post subject: | |
I know someone that had the CV joint come out when they were doing reverse donuts Pat |
|
| Author: | Mini Mad [ Fri Jul 08, 2005 7:20 pm ] |
| Post subject: | |
Still seems odd...go around a round-a-bout...hook it left, then right..spin the inside RH wheel around from weight transfer and direction of the wheels, then left to exit...spin the LH front... It depends which way the wheels are facing, as to which wheel will spin..maybe if wheels are dead centre, it prefer's the LH wheel? but if you turn it right it will spin the RH and turn left it will spin LH... |
|
| Author: | drmini in aust [ Fri Jul 08, 2005 7:23 pm ] |
| Post subject: | |
When they did the alignment, was it only the toe out they checked? Did they check castor and camber.. maybe something is bent or worn... 
|
|
| Author: | Lillee [ Fri Jul 08, 2005 8:20 pm ] |
| Post subject: | |
It's cause it's a clubby that's why Sorry couldn't resist
I was just about to say that, "Wheel alignment" is a badly used generalised term
|
|
| Author: | Mini Mad [ Fri Jul 08, 2005 8:26 pm ] |
| Post subject: | |
Your on a roll tonight aren't you chongly ..let's get a hack saw to lilly and put a clubby front on her 
Hmm...I got it aligned at Mr. Bob Janes..not sure what they did.. I know my diver's side tie rod has a little bit of a bend in it..passenger's side is straight... There is a knock also coming from this side when I take off...it's not engine related, definately suspension ball joint, bearing play maybe? Bearings got replaced a little over 6months ago though...timkens too..if i hold the wheel at 12 and 6 and try to rock it, there is about 1mm play total..drivers side has none..zip..squat.. It was up on a hoist today getting the exhaust done and I had a closer look, couldn't really find anything obvious... but i didn't get a great look.. |
|
| Author: | drmini in aust [ Fri Jul 08, 2005 8:31 pm ] |
| Post subject: | |
Assumption- by `tie rod' you do mean the tie bar that runs forward to subframe.. If a tie bar is bent, that will increase castor, and as the bottom arm is mounted at an angle, alter the camber a little bit too. 
Go buy some nice HD adjustable tie bars (& new rubbers) from Karcraft or somewhere..
Or, at least remove and straighten that bent one. |
|
| Author: | Lillee [ Fri Jul 08, 2005 8:32 pm ] |
| Post subject: | |
A knock when you take off: CV? Pot joint? are the rubbers all ok? Quote: let's get a hack saw to lilly and put a clubby front on her
Actually I might have to do this one day as there is rust up the front there
|
|
| Page 1 of 2 | All times are UTC + 10 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|