Have been lurking for a while, but finally bought a mini, so it seemed like time to say Hi!
I've bought a 1988 Rover UK import - currently unregistered, and will need a little bit of work to get it through the compliance process
| ausmini https://www.ausmini.com/forums/ |
|
| New member intro https://www.ausmini.com/forums/viewtopic.php?f=2&t=92880 |
Page 1 of 1 |
| Author: | Miraz [ Mon Jun 13, 2016 9:11 am ] |
| Post subject: | New member intro |
Have been lurking for a while, but finally bought a mini, so it seemed like time to say Hi! I've bought a 1988 Rover UK import - currently unregistered, and will need a little bit of work to get it through the compliance process
|
|
| Author: | Goldbrocade_62 [ Mon Jun 13, 2016 10:28 am ] |
| Post subject: | Re: New member intro |
Nice, the seats look comfy |
|
| Author: | AFF Motorsport [ Mon Jun 13, 2016 11:12 am ] |
| Post subject: | Re: New member intro |
Looks good, welcome 
|
|
| Author: | micool [ Mon Jun 13, 2016 11:26 am ] |
| Post subject: | Re: New member intro |
Looks great welcome to the mini family |
|
| Author: | Davo111 [ Mon Jun 13, 2016 11:43 am ] |
| Post subject: | Re: New member intro |
Welcome aboard, but pl,ease put your location in so people can see where your posting from, its much easier if you need help..... |
|
| Author: | miniman269 [ Mon Jun 13, 2016 12:41 pm ] |
| Post subject: | Re: New member intro |
Nice find..welcome Sent from my SM-G900I using Tapatalk |
|
| Author: | Miraz [ Mon Jun 13, 2016 5:49 pm ] |
| Post subject: | Re: New member intro |
Davo111 wrote: Welcome aboard, but pl,ease put your location in so people can see where your posting from, its much easier if you need help..... Done - doubtless will need some help soon, this one hasn't been driven for a couple of years and has a few rust spots that will need dealing with before they become major issues. |
|
| Author: | Lillee [ Tue Jun 14, 2016 9:11 am ] |
| Post subject: | Re: New member intro |
Welcome to Ausmini. Miraz wrote: Davo111 wrote: Welcome aboard, but pl,ease put your location in so people can see where your posting from, its much easier if you need help..... Done - doubtless will need some help soon, this one hasn't been driven for a couple of years and has a few rust spots that will need dealing with before they become major issues. I was about to say, "UK Import" = check for rust 
|
|
| Author: | 9YaTaH [ Tue Jun 14, 2016 9:15 am ] |
| Post subject: | Re: New member intro |
Lillee wrote: Welcome to Ausmini. I was about to say, "UK Import" = check for rust As were a bunch of others thinking the same
|
|
| Author: | Miraz [ Tue Jun 14, 2016 9:18 am ] |
| Post subject: | Re: New member intro |
On the basis of an initial inspection, it seems to be in surprisingly good condition on the rust front, so I'm hoping that I don't find any really nasty surprises as I dig deeper. So far the list is:- - Front Vallance - RHS A-Panel - RHS lower window frame - Both rear Seams - Both Rear floor corners Other than the Rear floor corners, it looks like just surface rust on the other locations - the floors have been patched badly before so we'll get those cut out and tied up properly. If the trail of paperwork is to be believed then it's had two previous owners, and has only covered 28,000 miles - mechanically it seems to be in reasonably good order. |
|
| Author: | 9YaTaH [ Thu Jun 16, 2016 9:07 am ] |
| Post subject: | Re: New member intro |
Reads like a good buy Jason 
|
|
| Page 1 of 1 | All times are UTC + 10 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|