Ausmini
It is currently Wed Jul 23, 2025 6:26 pm

All times are UTC + 10 hours




Post new topic Reply to topic  [ 16 posts ]  Go to page 1, 2  Next
Author Message
PostPosted: Mon Jan 16, 2017 2:24 pm 
Offline
1098cc
1098cc
User avatar

Joined: Wed Aug 06, 2008 10:14 am
Posts: 1370
Location: Sydney
Managed to fit new CV boots inner and outer without removing hub etc. as per my other post. Having problems securing the outer end of outer CV boot as so little clearance to hub assembly. Cable ties would not fit as the securing part stands high and would be ripped off when shaft turns. Wire is very hard to get around and tightened. Guess this might be why people take off the whole hub etc?

Any tips or tricks? Have removed the brake caliper assembly for a little more access but still doesn't seem possible to get the boot secured well.

_________________
Cooper S Mk2
Cooper S Mk1
ex Cooper S Mk2, various Morris 1100s, 1300s, 1500s, Leyland Sherpa!


Top
 Profile  
 
PostPosted: Mon Jan 16, 2017 2:42 pm 
Offline
848cc
848cc
User avatar

Joined: Fri Oct 11, 2013 12:49 pm
Posts: 125
to do it properly....the hub should moved off the CV joint and the grease completely wiped from the tightening area of the boot.
You can buy CV boot bands which clear the hub and look kosher to boot!

http://minisport.com.au/pair-of-outer-cv-boot-clipsastraps

_________________
....you just lost him his insurance bonus!

997


Top
 Profile  
 
PostPosted: Mon Jan 16, 2017 2:48 pm 
Offline
998cc
998cc
User avatar

Joined: Tue Sep 10, 2013 3:21 pm
Posts: 979
Location: St. George Area, New South Wales
Image

Get the tool for it too. Makes life easy.

_________________
Nick
Image
http://www.ausmini.com/forums/viewtopic.php?f=3&t=86675


Top
 Profile  
 
PostPosted: Mon Jan 16, 2017 2:52 pm 
Offline
religious status
religious status
User avatar

Joined: Fri Mar 19, 2004 6:19 pm
Posts: 39755
Location: near Baulkham Hills, NSW
You can also buy the straps cheap from CV joint repair shops.
If you don't have the proper tool you can get by with 2 pr of longnose pliers.

_________________
DrMini- 1970 wasaMatic 1360, Mk1S crank, 86.6HP (ATW) =~125 @ crank, 45 Dellorto (38 chokes), RE282 sprint cam, 1.5 rockers, 11.0:1 C/R. :mrgreen:


Top
 Profile  
 
PostPosted: Mon Jan 16, 2017 4:17 pm 
Offline
1098cc
1098cc

Joined: Sat Jul 23, 2011 8:17 am
Posts: 1964
Location: san remo nsw
Stainless cable ties.


Top
 Profile  
 
PostPosted: Mon Jan 16, 2017 4:23 pm 
Offline
1098cc
1098cc
User avatar

Joined: Wed Aug 06, 2008 10:14 am
Posts: 1370
Location: Sydney
Thanks guys,

No effective way of using any these mentioned items without removing hub, then?

_________________
Cooper S Mk2
Cooper S Mk1
ex Cooper S Mk2, various Morris 1100s, 1300s, 1500s, Leyland Sherpa!


Top
 Profile  
 
PostPosted: Mon Jan 16, 2017 4:51 pm 
Offline
998cc
998cc

Joined: Fri Apr 01, 2011 8:33 pm
Posts: 1196
All these (except the plastic cable ties) are possible options..(although i've never been flush enough the buy a tool that might be used every ten years or so)...Back when we also used soft tie wire ..

All options would be very difficult with the cv still mounted to the hub... which will be not as easy to remove now that things are disassembled..

I would re-attach the ball joints and place a large smooth bar (I use a short jemmy) threaded through the wheel studs to hold things steady while loosening the hub nut.

Cheers, Ian


Top
 Profile  
 
PostPosted: Mon Jan 16, 2017 9:08 pm 
Offline
848cc
848cc
User avatar

Joined: Tue Oct 09, 2012 9:57 am
Posts: 87
If you do the bars and wheel stud thing that Ian suggested, make sure you put nuts on the studs to avoid damaging the thread.

It can be done in situ, its just fiddly. Long pliers help.


Top
 Profile  
 
PostPosted: Tue Jan 17, 2017 10:07 am 
Offline
1275cc
1275cc
User avatar

Joined: Sat Jun 20, 2009 11:24 am
Posts: 2276
Location: Wollongong
I've noticed there are a couple of styles of CV. I have a mix on my car. Some the boot and groove is deeper into the hub and needs a really neat flush clip. Even the groove is different or in a different spot. I found in the end you save yourself a lot of cursing by undoing top and bottom ball joints and removing the hub and shaft complete and then as above you can get it all clean so the boot is not slipping around.


Sent from my iPhone using Tapatalk

_________________
Image
68 Morris Cooper S Mk1 (*ex 78 1275 LS 4th last built, 70 Morris 1500 OHC & 70 MiniMatic)


Top
 Profile  
 
PostPosted: Tue Jan 17, 2017 10:54 am 
Offline
848cc
848cc

Joined: Mon Sep 23, 2013 8:54 pm
Posts: 201
Location: Adelaide
peterb wrote:
Stainless cable ties.


I don't love stainless cable ties, they always loosen off about 3mm after they engage, and even with pliers I can't get them to stay tight enough

I like this type, they came with my last pair of boots. I have some Channellock multi-grips that have the perfect angle to do them up


You do not have the required permissions to view the files attached to this post.


Top
 Profile  
 
PostPosted: Tue Jan 17, 2017 12:27 pm 
Offline
1098cc
1098cc
User avatar

Joined: Wed Aug 06, 2008 10:14 am
Posts: 1370
Location: Sydney
Thanks again, all.

The groove is really inside the CV joint towards the hub, so looks like the hub will come off, as I don't want to do this again any time soon.....

Still can't get the grease out of my nails! :D

_________________
Cooper S Mk2
Cooper S Mk1
ex Cooper S Mk2, various Morris 1100s, 1300s, 1500s, Leyland Sherpa!


Top
 Profile  
 
PostPosted: Tue Jan 17, 2017 3:56 pm 
Offline
1275cc
1275cc
User avatar

Joined: Sat Jun 20, 2009 11:24 am
Posts: 2276
Location: Wollongong
Yeah it sounds like one like mine. The clip really needs to be flat and neat for clearance. If you take out the shaft and hub complete you could take it to a friendly cv place or mechanic either to get the good clips or them to do it.


Sent from my iPhone using Tapatalk

_________________
Image
68 Morris Cooper S Mk1 (*ex 78 1275 LS 4th last built, 70 Morris 1500 OHC & 70 MiniMatic)


Top
 Profile  
 
PostPosted: Tue Jan 17, 2017 4:41 pm 
Offline
religious status
religious status
User avatar

Joined: Fri Mar 19, 2004 6:19 pm
Posts: 39755
Location: near Baulkham Hills, NSW
New disc CVs are pretty easy to clip when in the hub, the clip is much closer to the edge of the CV than originals.

_________________
DrMini- 1970 wasaMatic 1360, Mk1S crank, 86.6HP (ATW) =~125 @ crank, 45 Dellorto (38 chokes), RE282 sprint cam, 1.5 rockers, 11.0:1 C/R. :mrgreen:


Top
 Profile  
 
PostPosted: Tue Jan 17, 2017 6:35 pm 
Offline
1275cc
1275cc
User avatar

Joined: Fri Oct 20, 2006 5:03 pm
Posts: 2729
Location: Out in the shed cleaning up my own mess.
Do yourself a favour, remove the hubs (as suggested by others) and when re-installing, take the opportunity to adjust hub float/bearing clearance and thus avoid unnecessary wear at the inner collars on the disc hubs. Betcha they need adjusting.

_________________
1967 Cooper S - new front bearings to do.
1965 Cooper S shell - Slow progress. No time or money!
1966 Deluxe- next rustoration!
Mk 2 & XJ6 Jags. Less said the better.


Last edited by AEG163job on Tue Jan 17, 2017 6:56 pm, edited 1 time in total.

Top
 Profile  
 
PostPosted: Tue Jan 17, 2017 6:55 pm 
Offline
1275cc
1275cc
User avatar

Joined: Fri Oct 20, 2006 5:03 pm
Posts: 2729
Location: Out in the shed cleaning up my own mess.
Oh, almost forgot. May as well check your ball-joints for wear too. For peace of mind.................. :wink:

_________________
1967 Cooper S - new front bearings to do.
1965 Cooper S shell - Slow progress. No time or money!
1966 Deluxe- next rustoration!
Mk 2 & XJ6 Jags. Less said the better.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 16 posts ]  Go to page 1, 2  Next

All times are UTC + 10 hours


Who is online

Users browsing this forum: No registered users and 111 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  

cron

© 2016 Ausmini. All garage work involves equal measures of enthusiasm, ingenuity and a fair degree of irresponsibility.