| ausmini https://www.ausmini.com/forums/ |
|
| rebuilding su's help? https://www.ausmini.com/forums/viewtopic.php?f=2&t=9481 |
Page 1 of 1 |
| Author: | h0nk [ Tue Jul 26, 2005 2:49 pm ] |
| Post subject: | rebuilding su's help? |
I'm just wondering if there is any trick with getting the jet bearing in the centre? I position it in the centre but it then moves to the side when I tighten the nut.. Do I just have to keep trying, or is there some trick to it? I've done one carby already and I think I got it pretty centre, but this second one is really hard.. JAM??? 
|
|
| Author: | J_A_M [ Tue Jul 26, 2005 3:06 pm ] |
| Post subject: | Re: rebuilding su's help? |
h0nk wrote: JAM???
 I didn't go there.....
replaced / renewed everthing except that. |
|
| Author: | h0nk [ Tue Jul 26, 2005 3:28 pm ] |
| Post subject: | |
haha stupid me.. should have left it alone, ah well I'll just try getting it as centre as possible |
|
| Author: | Wombat [ Tue Jul 26, 2005 3:44 pm ] |
| Post subject: | |
Manual tells you how - you do have a manual? |
|
| Author: | ziff [ Tue Jul 26, 2005 6:55 pm ] |
| Post subject: | |
I've completely stripped mine down and polished the whole thing lately and found that with mine I just had to be careful that I held it central when doing up the nut. Just be patient and hopefully it will work out for you. My problem is that I have had the dash pots chromed and now the plunger is sticking. Damn thing. 
Ziff |
|
| Author: | J_A_M [ Wed Jul 27, 2005 8:58 am ] |
| Post subject: | |
I bought chrome dashpot COVERS for JAM....  $30 for the pair.
|
|
| Author: | EST-071 [ Wed Jul 27, 2005 9:04 am ] |
| Post subject: | |
JAM what oil did you use for the dash pots. Pete |
|
| Author: | Hanra [ Wed Jul 27, 2005 1:25 pm ] |
| Post subject: | |
J_A_M wrote: I bought chrome dashpot COVERS for JAM....
$30 for the pair.Dash pot covers to suit 1 1/4 in or 1 1/2 in SU's???? Ive seen the 1 1/2in ones but never been able to get the 1 1/4 in covers! |
|
| Author: | Wolfman [ Wed Jul 27, 2005 1:38 pm ] |
| Post subject: | |
Hanra wrote: J_A_M wrote: I bought chrome dashpot COVERS for JAM.... $30 for the pair.Dash pot covers to suit 1 1/4 in or 1 1/2 in SU's???? Ive seen the 1 1/2in ones but never been able to get the 1 1/4 in covers! Yep you can get em for 1.25's I have a pair of red covers 
|
|
| Author: | J_A_M [ Wed Jul 27, 2005 1:59 pm ] |
| Post subject: | |
Pete, I used 20/50 Castrol motor oil. The dashpot covers I got are 1 1/4". UK ebay - $30 / pair NEW, landed on my door Very BLING! 
|
|
| Author: | EST-071 [ Wed Jul 27, 2005 2:04 pm ] |
| Post subject: | |
J_A_M wrote: Pete, I used 20/50 Castrol motor oil.
Thanks for that |
|
| Author: | Chris [ Thu Jul 28, 2005 12:30 am ] |
| Post subject: | Re: rebuilding su's help? |
h0nk wrote: I'm just wondering if there is any trick with getting the jet bearing in the centre?
Put the jet in and then assemble the dash pot and piston/needle assembly onto the carby. Lift and drop the piston and then tighten up the jet. After this the piston/needle assembly should fall to the jet with no hesitation. |
|
| Page 1 of 1 | All times are UTC + 10 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|