ausmini https://www.ausmini.com/forums/ |
|
Dutchy's Vtec - Round Nose, standard length https://www.ausmini.com/forums/viewtopic.php?f=23&t=89636 |
Page 7 of 15 |
Author: | Dutchy1978 [ Sun Feb 28, 2016 6:23 pm ] |
Post subject: | Re: Dutchy's Vtec - Round Nose, standard length |
I pulled the fuel tank out today and found some fuel seeping out the bottom. Thanks to all the feedback on the net I think POR15 tank sealer will be required. |
Author: | Dutchy1978 [ Sun Feb 28, 2016 6:23 pm ] |
Post subject: | Dutchy's Vtec - Round Nose, standard length |
Some feedback required about fuel tank capacities........how many kms/miles do people get out of their SPI/MPI tank with a B16A? Is it too small or OK? |
Author: | Harley [ Sun Feb 28, 2016 8:36 pm ] |
Post subject: | Re: Dutchy's Vtec - Round Nose, standard length |
Given the engine would have originally used around 8 litres / 100km or better, then you should be able to get 300km on a tank easily with a good reserve. My plan is to run standard tank and fit either a small fuel cell, right hand tank or just a big fuel cell later if I need more capacity. |
Author: | Dutchy1978 [ Mon Feb 29, 2016 6:06 am ] |
Post subject: | Re: Dutchy's Vtec - Round Nose, standard length |
I always wanted a RH tank as my supercharged engine used to chew up a fair bit of fuel. I pushed the button last night and ordered it. |
Author: | Dutchy1978 [ Sat Mar 05, 2016 4:36 pm ] |
Post subject: | Re: Dutchy's Vtec - Round Nose, standard length |
Mfactory LSD diff and final drive arrived. New diff bearings came with it too. Installing the bearings was as simple as heating them up with a heat gun till they started to smoke a little (this expands the bearing) then just dropped them onto the diff. No press required. I also painted the subframe and its components. Looks pretty good I think. |
Author: | Dutchy1978 [ Tue Mar 08, 2016 8:54 pm ] |
Post subject: | Re: Dutchy's Vtec - Round Nose, standard length |
Probably the best investment to date. Putting the engine in or out will be a breeze now. Wheel removal, suspension adjustments...the list goes on. I had to hang her from the ceiling though to get the hoist under but well worth it. |
Author: | simo74 [ Wed Mar 09, 2016 6:55 am ] |
Post subject: | Re: Dutchy's Vtec - Round Nose, standard length |
Loving this build thread keep, great work and keep the pictures coming. |
Author: | Dutchy1978 [ Sat Mar 26, 2016 10:05 pm ] |
Post subject: | Re: Dutchy's Vtec - Round Nose, standard length |
So I'm 2 days into a 4 day weekend and finally making some progress. Subframe was painted a couple of weeks ago so I was able to get straight into it. - Programmed the mini fuel sender to the Honda fuel gauge using the Spiyda fuel gauge wizard - Replaced the timing belt, tensioner, cam seals and crankshaft seal - Replaced the sump gasket (even painted the sump) - I mounted the new Walbro fuel pump to the original mini fuel pump bracket - I made up some 5mm steering rack limiters - Fitted the rocker cover with new gaskets - Put the engine into the subframe (For the last time. Fingers crossed) - Alternator and belt fitted Then lowered the car onto the engine. The new hoist made this part simple. Worth every penny. |
Author: | Mokesta [ Mon Mar 28, 2016 9:12 pm ] |
Post subject: | Re: Dutchy's Vtec - Round Nose, standard length |
NICE! Great work. |
Author: | Hobson [ Tue Mar 29, 2016 1:06 pm ] |
Post subject: | Re: Dutchy's Vtec - Round Nose, standard length |
Bet you are itching for a drive now. that is if you weren't before. |
Author: | Dutchy1978 [ Wed Mar 30, 2016 8:03 am ] |
Post subject: | Re: Dutchy's Vtec - Round Nose, standard length |
Hobson wrote: Bet you are itching for a drive now. that is if you weren't before. Your not wrong. So close yet so far. |
Author: | Dutchy1978 [ Wed Mar 30, 2016 3:34 pm ] |
Post subject: | Re: Dutchy's Vtec - Round Nose, standard length |
Good to know. If I use my 13x6 sport pack wheels then I might not need them so easier to remove if not require. |
Author: | Dutchy1978 [ Tue Apr 12, 2016 9:48 pm ] |
Post subject: | Dutchy's Vtec - Round Nose, standard length |
Progress on the car at the moment is a bit like building a house. Right now I'm at that stage where heaps is getting done but from the outside it looks like nothing has changed. Brake lines done. Some creative bending to make it fit. Drive shafts together New wheel bearings installed New brake discs New 4 pot minisport calipers Suspension fitted |
Author: | Maelgwn [ Tue Apr 12, 2016 11:43 pm ] |
Post subject: | Re: Dutchy's Vtec - Round Nose, standard length |
Hey Dutchy, What's the weight difference between the two engine set ups, do you need to upgrade the spring you have hiding in there and the dampers? Maelgwn P.S Loving the build log, great work |
Page 7 of 15 | All times are UTC + 10 hours |
Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |