ausmini
https://www.ausmini.com/forums/

datsun 1600 twin carbs (1 on mini)
https://www.ausmini.com/forums/viewtopic.php?f=5&t=41874		 Page 1 of 3
Author:  cookie720 [ Sat May 10, 2008 11:42 am ]
Post subject:  datsun 1600 twin carbs (1 on mini)
I got a set of twin carbs from a datsun and i want to put 1 on my mini, I think they are 1.5" Can this be done. Got some pics

Image
Image
Image
Image
Image

Thanks
Author:  spraycanmansam [ Sat May 10, 2008 7:48 pm ]
Post subject: 
Why not use both? They look like a normal set of twin SU's too me, not the Hitachi's that Datto's originally came with. I'd be getting a twin manifold :wink:
Author:  mini-dunger [ Sat May 10, 2008 8:04 pm ]
Post subject: 
they look as though they are in good nic too. Good score.
Author:  Mick [ Sat May 10, 2008 9:19 pm ]
Post subject: 
I like the knurled nut for the mixtures....were these made under license in japan does anyone know? Or did minis get the budget 1.5 inch SUs?
Author:  Morris 1100 [ Sat May 10, 2008 9:21 pm ]
Post subject: 
Jap copies. Made under license. (Mikuni? :? )

I wonder if the SU needles fit? If they don't it could be a problem getting the right needle for the job.
Author:  cookie720 [ Sat May 10, 2008 9:47 pm ]
Post subject: 
spraycanmansam wrote:
Why not use both? They look like a normal set of twin SU's too me, not the Hitachi's that Datto's originally came with. I'd be getting a twin manifold :wink:


because my engine is a stock 1100
Author:  sociallydisabled [ Sun May 11, 2008 8:31 pm ]
Post subject: 
time for a engine build :P
Author:  cookie720 [ Sun May 11, 2008 9:29 pm ]
Post subject: 
time i have, money on the other hand :(
Author:  sociallydisabled [ Sun May 11, 2008 9:31 pm ]
Post subject: 
ahh yes... the major factor to anything...aint it a shame haha
Author:  spraycanmansam [ Sun May 11, 2008 9:44 pm ]
Post subject: 
How much do you want for the other one? :wink:
Author:  spraycanmansam [ Sun May 11, 2008 9:46 pm ]
Post subject: 
Morris 1100 wrote:
Jap copies. Made under license. (Mikuni? :? )

I wonder if the SU needles fit? If they don't it could be a problem getting the right needle for the job.


They look like SU's to me :? I thought the Hitachi's were the Jap copy ---

Image
Author:  Morris 1100 [ Sun May 11, 2008 9:53 pm ]
Post subject: 
The Japs (Hitachi) made both dome top and flat top SU copies.
Author:  spraycanmansam [ Sun May 11, 2008 9:57 pm ]
Post subject: 
Ah...



:lol:
Author:  Blokeinamoke [ Sun May 11, 2008 10:28 pm ]
Post subject: 
Morris 1100 wrote:
Jap copies. Made under license. (Mikuni? :? )

I wonder if the SU needles fit? If they don't it could be a problem getting the right needle for the job.


Some parts fit and some dont. Better made than SUs. The piston spring is different ( variable if I remember correctly) to the standard SU options.
Author:  Asphalt [ Sun May 11, 2008 10:55 pm ]
Post subject: 
Blokeinamoke wrote:
Some parts fit and some dont. Better made than SUs.


Haha, that's not hard to do, thought.

My HS4:
Image
Image

Anyways:
If the SU needles fit (easy to figure out) - why not use em?
They seem to have some fine improvements in design.

Cheers,
Jan

PS: To be fair: my HIF44 is almost PERFEKT worked up!!
Page 1 of 3 All times are UTC + 10 hours
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/