Ausmini
It is currently Wed Aug 06, 2025 9:14 am

Board index » Mini Chat » Mini Chat

All times are UTC + 10 hours




Post new topic Reply to topic  Page 1 of 1
  [ 11 posts ] 
  Print view Previous topic | Next topic 
Author Message
Klubman
 Post subject: Gauges Mini K
PostPosted: Sat Jan 21, 2006 5:43 pm 
Offline
848cc
848cc

Joined: Fri Jul 29, 2005 12:00 am
Posts: 170
Location: Croydon Victoria
My temp and fuel don't work, is the voltage stabilser still available?
All my earths seem OK.
Nigel

_________________
Mini K, 1310, Jet Red/Crystal White Roof, Rover Interior

75 Clubman
Top
 Profile  
 
drmini in aust
 Post subject:
PostPosted: Sat Jan 21, 2006 6:51 pm 
Offline
religious status
religious status
User avatar

Joined: Fri Mar 19, 2004 6:19 pm
Posts: 39764
Location: near Baulkham Hills, NSW
PM `wombat' on this forum, he can sell you an electronic one cheap, so you can throw that 1950 technology away. I use them in both cars. :wink:

_________________
DrMini- 1970 wasaMatic 1360, Mk1S crank, 86.6HP (ATW) =~125 @ crank, 45 Dellorto (38 chokes), RE282 sprint cam, 1.5 rockers, 11.0:1 C/R. :mrgreen:
Top
 Profile  
 
Drekkus
 Post subject:
PostPosted: Sat Jan 21, 2006 7:08 pm 
Offline
848cc
848cc

Joined: Sun May 09, 2004 6:12 pm
Posts: 267
Location: Adelaide
I bought a $7 voltage selector kit from Jaycar, ditched the selector resistors and, from memory, replaced them with a 3.3k ohm resistor to give a theoretical voltage or 10v.The measured voltage turned out to be a steady 9.9v.Place it into a small jiffy box and stick it behind the speedo. Seems to work well so far and its all mounted securely on a proper circuit board..
Top
 Profile  
 
drmini in aust
 Post subject:
PostPosted: Sat Jan 21, 2006 7:30 pm 
Offline
religious status
religious status
User avatar

Joined: Fri Mar 19, 2004 6:19 pm
Posts: 39764
Location: near Baulkham Hills, NSW
wombat uses a 10V voltage regulator chip, he just puts a couple of flying leads and spade lugs on it.
3 wires: 12VDC in, ground, 10VDC out. :wink:
no need to put it in a can with his latest version.

_________________
DrMini- 1970 wasaMatic 1360, Mk1S crank, 86.6HP (ATW) =~125 @ crank, 45 Dellorto (38 chokes), RE282 sprint cam, 1.5 rockers, 11.0:1 C/R. :mrgreen:
Top
 Profile  
 
kazjim
 Post subject:
PostPosted: Sat Jan 21, 2006 7:31 pm 
Offline
1098cc
1098cc
User avatar

Joined: Tue Apr 06, 2004 2:49 pm
Posts: 1556
Location: Central Coast, NSW
And Wombats one is a single transistor !

you can even put it inside the original "Can" if you want.....

Not saying yours isnt good Drekkus, but the Transistor one is superb...

Got one in the Brick... not a single problem in over 2 years so far !

J

_________________
Image
Top
 Profile  
 
Drekkus
 Post subject:
PostPosted: Sat Jan 21, 2006 7:39 pm 
Offline
848cc
848cc

Joined: Sun May 09, 2004 6:12 pm
Posts: 267
Location: Adelaide
Yeah, I tried going with the transistor method but for some reason I couldn't get it to work, It just kept overheating.The kit was my second choice but I'm happy with results.
Top
 Profile  
 
Mike
 Post subject:
PostPosted: Sun Jan 22, 2006 12:32 pm 
Offline
1098cc
1098cc
User avatar

Joined: Tue Mar 16, 2004 10:39 pm
Posts: 1629
Location: Sydney, E. Burbs
.l


Last edited by Mike on Sun Jan 22, 2006 12:32 pm, edited 1 time in total.

Top
 Profile  
 
Mike
 Post subject:
PostPosted: Sun Jan 22, 2006 12:32 pm 
Offline
1098cc
1098cc
User avatar

Joined: Tue Mar 16, 2004 10:39 pm
Posts: 1629
Location: Sydney, E. Burbs
My fuel gauge jumped to full 3 days ago and stays there (obviously it does go back with the ign. off). Does this sound like a dead volt. reg.?

Temp gauge seems to work ok btw.
Top
 Profile  
 
drmini in aust
 Post subject:
PostPosted: Sun Jan 22, 2006 2:43 pm 
Offline
religious status
religious status
User avatar

Joined: Fri Mar 19, 2004 6:19 pm
Posts: 39764
Location: near Baulkham Hills, NSW
It could be. Those old 10V so-called voltage stabilizers do weird things when old. Usually whan they go dud, you get either 13+V or 0V. But mine used to give 10V at idle, then the faster you went the less it gave, due to vibration. So the fuel gauge used to drop with speed, then when I stopped it came back up. :?
I flung the stabilizer and fitted wombat's electronic one, and it's read fine ever since. :D

_________________
DrMini- 1970 wasaMatic 1360, Mk1S crank, 86.6HP (ATW) =~125 @ crank, 45 Dellorto (38 chokes), RE282 sprint cam, 1.5 rockers, 11.0:1 C/R. :mrgreen:
Top
 Profile  
 
Mike
 Post subject:
PostPosted: Tue Jan 24, 2006 6:55 am 
Offline
1098cc
1098cc
User avatar

Joined: Tue Mar 16, 2004 10:39 pm
Posts: 1629
Location: Sydney, E. Burbs
Cheers Doc - I'll get it anyway and see if that helps.
Top
 Profile  
 
Wombat
 Post subject:
PostPosted: Wed Jan 25, 2006 5:30 pm 
Offline
1360cc
1360cc
User avatar

Joined: Mon Jul 26, 2004 7:23 am
Posts: 7339
Location: Sunny Shine Coast, Qld Australia
$15 including postage PM me your address and I'll reply with payment details :wink:

_________________
David L
Image

My greatest fear in life is that when I die my wife will sell my Mini and tools for the price I told her I paid for them!
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 11 posts ] 

Board index » Mini Chat » Mini Chat

All times are UTC + 10 hours


Who is online

Users browsing this forum: Bing [Bot] and 97 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  

© 2016 Ausmini. All garage work involves equal measures of enthusiasm, ingenuity and a fair degree of irresponsibility.