Ausmini
It is currently Sun Jul 20, 2025 1:28 am

Board index » Mini Chat » Mini & A/A+ Series Mods

All times are UTC + 10 hours




Post new topic Reply to topic  Page 1 of 1
  [ 11 posts ] 
  Print view Previous topic | Next topic 
Author Message
spraycanmansam
PostPosted: Tue Mar 03, 2009 12:51 pm 
Offline
Forum Graffiti
User avatar

Joined: Sat Jun 16, 2007 10:31 pm
Posts: 1640
I have an A series manifold with the markings 12G 299 (pretty sure its off an MG 1100)

Question... are the mountings for the carbs (not the ports) closer together than a mini twin carb manifold? I have ran into quite a dilemma... :? :P


Last edited by spraycanmansam on Tue Mar 03, 2009 7:35 pm, edited 1 time in total.

Top
 Profile  
 
drmini in aust
 Post subject:
PostPosted: Tue Mar 03, 2009 1:42 pm 
Offline
religious status
religious status
User avatar

Joined: Fri Mar 19, 2004 6:19 pm
Posts: 39754
Location: near Baulkham Hills, NSW
Pretty sure they are, read this thread where all the twin carb manifolds are discussed.
http://www.minimania.com/web/threadid/8 ... thread.cfm

_________________
DrMini- 1970 wasaMatic 1360, Mk1S crank, 86.6HP (ATW) =~125 @ crank, 45 Dellorto (38 chokes), RE282 sprint cam, 1.5 rockers, 11.0:1 C/R. :mrgreen:
Top
 Profile  
 
spraycanmansam
 Post subject:
PostPosted: Tue Mar 03, 2009 2:13 pm 
Offline
Forum Graffiti
User avatar

Joined: Sat Jun 16, 2007 10:31 pm
Posts: 1640
That's a good read.. bookmarked :D
After reading that, it appears they are ~1/2" narrower... that would explain why my filters hit :x

Anybody got a twin manifold for a mini? :D :P
Top
 Profile  
 
drmini in aust
 Post subject:
PostPosted: Tue Mar 03, 2009 2:22 pm 
Offline
religious status
religious status
User avatar

Joined: Fri Mar 19, 2004 6:19 pm
Posts: 39754
Location: near Baulkham Hills, NSW
spraycanmansam wrote:
That's a good read.. bookmarked :D
After reading that, it appears they are ~1/2" narrower... that would explain why my filters hit :x

Anybody got a twin manifold for a mini? :D :P

I don't know why BMC made that manifold narrow... :?

There are lots of different ones out there, and most of the aftermarket ones (eg Lynx or Peter Manton) flow better than the factory ones did.
Whichever you get, watch the ports align properly and there are no bad casting lumps inside.
I just took a Minispares intake manifold off a 1275 Metro motor, the ports were both misaligned by 3mm.. :shock:

_________________
DrMini- 1970 wasaMatic 1360, Mk1S crank, 86.6HP (ATW) =~125 @ crank, 45 Dellorto (38 chokes), RE282 sprint cam, 1.5 rockers, 11.0:1 C/R. :mrgreen:
Top
 Profile  
 
KLAS
 Post subject:
PostPosted: Tue Mar 03, 2009 3:50 pm 
Offline
998cc
998cc
User avatar

Joined: Thu May 18, 2006 4:57 am
Posts: 515
Location: Hamburg, Germany
drmini in aust wrote:
I just took a Minispares intake manifold off a 1275 Metro motor, the ports were both misaligned by 3mm.. :shock:


great, the quality is getting better and better :wink:

_________________
Rover 214 atm ....
Top
 Profile  
 
drmini in aust
 Post subject:
PostPosted: Tue Mar 03, 2009 6:30 pm 
Offline
religious status
religious status
User avatar

Joined: Fri Mar 19, 2004 6:19 pm
Posts: 39754
Location: near Baulkham Hills, NSW
KLAS wrote:
drmini in aust wrote:
I just took a Minispares intake manifold off a 1275 Metro motor, the ports were both misaligned by 3mm.. :shock:


great, the quality is getting better and better :wink:

Not a bad manifold, IF the stud holes were in the right place.:mrgreen:
I'll take GR's 7" one instead thanks, it gives more mumbo. :wink:

_________________
DrMini- 1970 wasaMatic 1360, Mk1S crank, 86.6HP (ATW) =~125 @ crank, 45 Dellorto (38 chokes), RE282 sprint cam, 1.5 rockers, 11.0:1 C/R. :mrgreen:
Top
 Profile  
 
spraycanmansam
 Post subject:
PostPosted: Tue Mar 03, 2009 7:33 pm 
Offline
Forum Graffiti
User avatar

Joined: Sat Jun 16, 2007 10:31 pm
Posts: 1640
Hmm.. I'm torn :?

Should I sell off the twins I've just bought and invest in a 7" GR manifold, reco kit and K&N filter for my HS6?

I really love the look of a nice set of twins tho... 8)

If it helps, the motor that's being built at the moment is an 1152cc with a 12G295 head, around 9.5-10:1 compression and I'm thinking I'll go with a 266 cam (I don't want anything too lairy as it's for my girlfriend to putt around in :P)

Any opinions would be great :)


Last edited by spraycanmansam on Tue Mar 03, 2009 7:43 pm, edited 1 time in total.

Top
 Profile  
 
sgc
 Post subject:
PostPosted: Tue Mar 03, 2009 7:39 pm 
Offline
This space for rent
User avatar

Joined: Thu Feb 08, 2007 12:40 pm
Posts: 5455
Location: Melbourne
spraycanmansam wrote:
Any opinions would be great :)


That describes my engine pretty much to the 'T'.. my opinion is naturally that it's an excellent combination :D

_________________
Simon

The adventures of an owner builder in the Tallarook Ranges

Image
Top
 Profile  
 
drmini in aust
 Post subject:
PostPosted: Tue Mar 03, 2009 9:20 pm 
Offline
religious status
religious status
User avatar

Joined: Fri Mar 19, 2004 6:19 pm
Posts: 39754
Location: near Baulkham Hills, NSW
Twins do go well on a 1098. Look great too.
Just make sure they are a GOOD pair in GOOD (preferably reco) condition. :wink:

_________________
DrMini- 1970 wasaMatic 1360, Mk1S crank, 86.6HP (ATW) =~125 @ crank, 45 Dellorto (38 chokes), RE282 sprint cam, 1.5 rockers, 11.0:1 C/R. :mrgreen:
Top
 Profile  
 
spraycanmansam
 Post subject:
PostPosted: Tue Mar 03, 2009 9:32 pm 
Offline
Forum Graffiti
User avatar

Joined: Sat Jun 16, 2007 10:31 pm
Posts: 1640
drmini in aust wrote:
Twins do go well on a 1098. Look great too.
Just make sure they are a GOOD pair in GOOD (preferably reco) condition. :wink:


I'm veeery happy with the price I paid for them with the condition they're in. They've had kits put through them, new throttle shafts, bushes, etc. They're in great condition :D ..and yeah Im not keen on doing a 'Tiny' :P I think I'll stick with the twins 8)

How does one tell if they're a proper pair? They don't have tags, but the numbers on the bodies are: AUC871 and AUC870
Top
 Profile  
 
simon k
 Post subject:
PostPosted: Mon Mar 09, 2009 12:07 pm 
Offline
Yay For Hay!
User avatar

Joined: Wed Sep 08, 2004 9:27 pm
Posts: 15912
Location: Wodonga - Vic/NSW border
spraycanmansam wrote:
AUC871 and AUC870


MK2 S if I recall correctly... do a search

_________________
did I tell you that I won a trophy?
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 11 posts ] 

Board index » Mini Chat » Mini & A/A+ Series Mods

All times are UTC + 10 hours


Who is online

Users browsing this forum: No registered users and 29 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  

© 2016 Ausmini. All garage work involves equal measures of enthusiasm, ingenuity and a fair degree of irresponsibility.