Ausmini
It is currently Mon Jul 21, 2025 12:23 am

Board index » Mini Chat » Mini Chat

All times are UTC + 10 hours




Post new topic Reply to topic  Page 1 of 2
  [ 30 posts ]  Go to page 1, 2  Next
  Print view Previous topic | Next topic 
Author Message
Gadgets mini
 Post subject: RUNNING LEAN HOT OR NOT
PostPosted: Fri Feb 25, 2005 3:44 pm 
Offline
Resident Haemorrhoid
User avatar

Joined: Mon Jan 31, 2005 7:47 pm
Posts: 6815
Location: in da ACT
To all the learned Mini folk
I have just fitted a refurbed HS4 Single SU to my clubbie 1098 and it is running well. but today in Canberra the temp was 32 deg c and at 100kmh on a good stretch the temp climbed slowly to 220 deg far or 104 deg cel.

my question is if its leaning out will it cause it over heat (thats what I think )or is the above temps normal operating range considering the ambient temp and im just being paraniod :?

if it is leaning out I need to richen the mix (turning clockwise ) Right ?
and would it be best to fit a supplimental radiator(old heater core) behind the grill?

Any Suggestions please

Enjoy your weekend


Cheers

_________________
mtsmini wrote:
Master, you are wise beyond your years.....I am a mere grasshopper before you :D

Tombo wrote:
Gadgets has never been so right :D
Top
 Profile  
 
9YaTaH
PostPosted: Fri Feb 25, 2005 4:44 pm 
Offline
1360cc
1360cc
User avatar

Joined: Sun Apr 11, 2004 11:32 am
Posts: 12390
Location: Sthrn HiLoLands, NSW, Australia
Gadgets mini wrote:
To all the learned Mini folk
I have just fitted a refurbed HS4 Single SU to my clubbie 1098 and it is running well. but today in Canberra the temp was 32 deg c and at 100kmh on a good stretch the temp climbed slowly to 220 deg far or 104 deg cel.

my question is if its leaning out will it cause it over heat (thats what I think )or is the above temps normal operating range considering the ambient temp and im just being paraniod :?

if it is leaning out I need to richen the mix (turning clockwise ) Right ?
and would it be best to fit a supplimental radiator(old heater core) behind the grill?

Any Suggestions please

Enjoy your weekend


Cheers


Hard to say it really is the mixture...but a lean mixture will cause overheating....did the radiator bubble over when you stopped or show other signs that the cooling system was stressed....

did it tend to run hot before with the twins??

_________________
"Show me the Mini!"
Top
 Profile  
 
Gadgets mini
 Post subject:
PostPosted: Fri Feb 25, 2005 4:53 pm 
Offline
Resident Haemorrhoid
User avatar

Joined: Mon Jan 31, 2005 7:47 pm
Posts: 6815
Location: in da ACT
Afternoon Mick
no the radiator didnt appear to bubble over or show signs of stress when i coasted for a bit down hill the temp dropped then came up again under power.
the temp was fine with the twins and i did not change anything when i changed the carbie at least i can get it to idle below 1000 rev now. :)

im picking up a 71 clubbie shell tomorrrow so the collection grows. :D

all going well ill see you tuesday at the Carilion perhaps

Cheers
Gadget

_________________
mtsmini wrote:
Master, you are wise beyond your years.....I am a mere grasshopper before you :D

Tombo wrote:
Gadgets has never been so right :D
Top
 Profile  
 
min13k
 Post subject:
PostPosted: Fri Feb 25, 2005 4:58 pm 
Offline
I DWIVE A BIG TWUCK
I DWIVE A BIG TWUCK
User avatar

Joined: Tue Mar 16, 2004 5:17 pm
Posts: 8732
i want a white 71 clubby interior
makka

_________________
Anonymous moderation means the agro that is built up towards the mods isn't aimed at an individual (fewer "Makk" attacks). Less stress for mods means less moderator "retirements".
Top
 Profile  
 
Stuartminidlx
 Post subject:
PostPosted: Fri Feb 25, 2005 5:08 pm 
Offline
848cc
848cc
User avatar

Joined: Fri Jan 07, 2005 10:17 pm
Posts: 460
Location: Sydney
coolant boils at around 120*C (correct me if i'm wrong plz) and it's a fairly soild block. so i wouldn't worry about it. check your temp gauge to. http://www.hotbricks.org.au/ thats a good link with intructions. my only recomendation would be to use cooling when boil instead of water because u can hold it a 100*C with out it boiling. fast way to check is when the car is cold take the rad cap of and start it up and hold a thermometer in the rad and till it stops rising and just see what temp it really running at. because my car sit in the red all day but it is realy only at about 85*C

feel free to correct me if i'm wrong with anything. i like to leard so any advice is good.

_________________
FOR SALE MInidlx, 1293, GR head, RE-13, GR worked Redline Manifold, 45 mm DCOE,pulsar dizzy , "S" Disc's, Mk II "S" box, 3.65 diff. Minator 10X6's On the loose
Image
Top
 Profile  
 
9YaTaH
 Post subject: mixture...it sounds like
PostPosted: Fri Feb 25, 2005 8:05 pm 
Offline
1360cc
1360cc
User avatar

Joined: Sun Apr 11, 2004 11:32 am
Posts: 12390
Location: Sthrn HiLoLands, NSW, Australia
Gadgets mini wrote:
Afternoon Mick
no the radiator didnt appear to bubble over or show signs of stress when i coasted for a bit down hill the temp dropped then came up again under power.
the temp was fine with the twins and i did not change anything when i changed the carbie at least i can get it to idle below 1000 rev now. :)

im picking up a 71 clubbie shell tomorrrow so the collection grows. :D

all going well ill see you tuesday at the Carilion perhaps

Cheers
Gadget


Hmmm based on what you have said.... then...richen up the mixture....hmmm...if I had known today I would have put you in touch with CPOCSM in R8....he has a colortune plug.....

Just richen it up an watch what happens ...maybe call into Melba Motors sat morn...Mick might be able to give it a quick tweak...(tell him you are from the Mini Club)

_________________
"Show me the Mini!"
Top
 Profile  
 
CPOCSM
 Post subject: Cooling Problem
PostPosted: Fri Feb 25, 2005 9:34 pm 
Offline
1275cc
1275cc
User avatar

Joined: Fri Aug 13, 2004 3:45 am
Posts: 2360
Location: SE QLD
Gday Gadget - well I can vouch for the heater core on the grille - I never had an issue with the heating up but was paranoid none the less. The way I nstalled it was I plumbed from the bottom hose, into the existing heater core, back out into the engine bay, into the second heater core mounted in the front grille near the fresh air intake snout, then into the cylinder head. I got to about a third of the way up the scale today but I was fanging it. The temp on the monaro just managed to get above the cold mark so I am confident the second core will help.

I have the gunsons colourtune here if you want to check the cars mixture but also check the carb too. Is the needle correct (ADF or AX?) but I am sure between the noggins here we can sort out your woes

Hooroo for now...

Rob Forsyth
Miniot!

_________________
Rob Forsyth
Miniot!!
Top
 Profile  
 
low n blown
 Post subject:
PostPosted: Sat Feb 26, 2005 8:56 am 
Offline
1098cc
1098cc

Joined: Tue Aug 24, 2004 3:57 pm
Posts: 1478
Location: queensland
before you richen it up check you dont have a leak at the manifold head junction. You can avoid this using Maniseal "available at all your good auto outlets". If you have a slight leak it will cause you to run lean and you can get overheating problems. Alternatively just a side thought, are you running a thermostat. Not running a thermo can speed up flow of the coolant and actually cause overheating under load. It may even be worth replacing yours if it is a little old.

_________________
1970 Cooper S ex-Bathurst & ATCC
1964 Austin Cooper S ex-Group C race car
1967 Morris Cooper S ex-Group B
1962 Mini Speed sports sedan
1968-71 ex-Peter Manton Shell car
Top
 Profile  
 
9YaTaH
 Post subject: Good Advice!
PostPosted: Sat Feb 26, 2005 11:05 am 
Offline
1360cc
1360cc
User avatar

Joined: Sun Apr 11, 2004 11:32 am
Posts: 12390
Location: Sthrn HiLoLands, NSW, Australia
low'n blown wrote:
before you richen it up check you dont have a leak at the manifold head junction. You can avoid this using Maniseal "available at all your good auto outlets". If you have a slight leak it will cause you to run lean and you can get overheating problems. Alternatively just a side thought, are you running a thermostat. Not running a thermo can speed up flow of the coolant and actually cause overheating under load. It may even be worth replacing yours if it is a little old.


Gadge...you could also put some drops of oil along the manifold gasket line to see if it gets blown/sucked.....whatever...don't go overboard with the oil though!!

You can run withouit a thermostat so long as you leave a restrictor plate to slow the coolant down so that it stays long enough in the radiator to get ...well.....cooled!

What sort of container does Maniseal come in low'n blown? a tube?

_________________
"Show me the Mini!"
Top
 Profile  
 
Gadgets mini
 Post subject:
PostPosted: Sun Feb 27, 2005 12:09 pm 
Offline
Resident Haemorrhoid
User avatar

Joined: Mon Jan 31, 2005 7:47 pm
Posts: 6815
Location: in da ACT
Many thanks to all for their advice :D :D

i think ive got it sorted (turned it clockwise 1/2 turn ) wiil see how i go

Mick, Rob hopefully catch up on Tuesday

Thanks again :)

_________________
mtsmini wrote:
Master, you are wise beyond your years.....I am a mere grasshopper before you :D

Tombo wrote:
Gadgets has never been so right :D
Top
 Profile  
 
min13k
 Post subject:
PostPosted: Mon Feb 28, 2005 12:00 am 
Offline
I DWIVE A BIG TWUCK
I DWIVE A BIG TWUCK
User avatar

Joined: Tue Mar 16, 2004 5:17 pm
Posts: 8732
mick wd40 is good for that you spray if the motor revs higher you have a vacume
makka

_________________
Anonymous moderation means the agro that is built up towards the mods isn't aimed at an individual (fewer "Makk" attacks). Less stress for mods means less moderator "retirements".
Top
 Profile  
 
NAV
 Post subject:
PostPosted: Mon Feb 28, 2005 10:56 am 
Offline
NAV-MAN
User avatar

Joined: Sun Jul 18, 2004 1:50 am
Posts: 1672
Location: Nothern Brisvegas
I would look at everything just to make sure that it's running well.
I.E. Plugs, points, leads, dizzy cap, rotor button, ignition timing, vacuum advance working. Had the radiator checked recently?

By just tweaking the fuel mixture you can mask the real problem and end up with a petrol guzzler

_________________
Image
Top
 Profile  
 
miniclubman
PostPosted: Wed Mar 09, 2005 10:48 pm 
Offline
848cc
848cc
User avatar

Joined: Thu Apr 15, 2004 7:26 am
Posts: 53
Location: Sunbury Victoria
Gadgets mini wrote:
To all the learned Mini folk
I have just fitted a refurbed HS4 Single SU to my clubbie 1098 and it is running well. but today in Canberra the temp was 32 deg c and at 100kmh on a good stretch the temp climbed slowly to 220 deg far or 104 deg cel.

my question is if its leaning out will it cause it over heat (thats what I think )or is the above temps normal operating range considering the ambient temp and im just being paraniod :?

if it is leaning out I need to richen the mix (turning clockwise ) Right ?
and would it be best to fit a supplimental radiator(old heater core) behind the grill?

Any Suggestions please

Enjoy your weekend

I was running the same carby on my 1275 Moke and had exactly the same temp problem, convinced it was a lean problem threw away the carb and put twin SU's on and instant drop from 220 on a hot day to 190.

Regards miniclubman


Cheers

_________________
My Nissan is Just Transport But my MINI is FUN !!
Top
 Profile  
 
Spaceboy
 Post subject:
PostPosted: Thu Mar 10, 2005 10:32 am 
Offline
1360cc
1360cc

Joined: Mon Nov 01, 2004 4:36 pm
Posts: 7673
make sure your fan belt is in good condition if its knackered it may not be turning the fan as fast as it should.
Top
 Profile  
 
J_A_M
PostPosted: Thu Mar 10, 2005 10:36 am 
Offline
1360cc
1360cc

Joined: Tue Mar 16, 2004 11:32 am
Posts: 9068
Gadgets mini wrote:
if it is leaning out I need to richen the mix (turning clockwise ) Right ?


Turning what? What's the adjustment and where is it?
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 2
  [ 30 posts ]  Go to page 1, 2  Next

Board index » Mini Chat » Mini Chat

All times are UTC + 10 hours


Who is online

Users browsing this forum: No registered users and 86 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  

cron

© 2016 Ausmini. All garage work involves equal measures of enthusiasm, ingenuity and a fair degree of irresponsibility.