Ausmini
It is currently Sat Aug 23, 2025 3:08 pm

Board index » Mini Chat » Mini Chat

All times are UTC + 10 hours




Post new topic Reply to topic  Page 2 of 2
  [ 24 posts ]  Go to page Previous  1, 2
  Print view Previous topic | Next topic 
Author Message
thomas_hb
 Post subject:
PostPosted: Sun Jun 19, 2011 5:29 pm 
Offline
998cc
998cc
User avatar

Joined: Fri Feb 18, 2011 4:21 pm
Posts: 644
Location: Sydney, NSW
The wire which doesn't go to the coil should be an earth.

Red is never an earth (even the dodgiest of backyard mechanics wouldn't be so cruel as to start earthing things with a red wire... I hope!) so I think you may be looking at the wrong wire, or a positive feed as been connected where it shouldn't be.

Can you put in a known good earth (i.e. patch a wire direct to bare metal) to prove the above hypothesis?

It should be a simple two wire set up. One wire to the positive terminal on the coil. One wire to earth. If you get that done the rest should look after itself.
Top
 Profile  
 
thomas_hb
 Post subject:
PostPosted: Sun Jun 19, 2011 5:35 pm 
Offline
998cc
998cc
User avatar

Joined: Fri Feb 18, 2011 4:21 pm
Posts: 644
Location: Sydney, NSW
Quote:
Already did that, It drops back to zero Confused


Try the other spade?? If it shoots to 8K it means you've connected it directly to a constant positive.
Top
 Profile  
 
Petesmini
 Post subject: Headlight Upgrade
PostPosted: Sun Jun 19, 2011 5:44 pm 
Offline
848cc
848cc

Joined: Sun May 29, 2011 4:07 pm
Posts: 53
Location: Ardlethan, NSW
Guys,

I know that RED is never used as an earth under any circumstances, that much I remember from my electrics classes. :lol:

The wiring is I am describing is standard on all leyland 'S' minis. :?

I agree that one should be power & one should be earth. :)

Cheers Pete

_________________
December 1976 Leyland Mini S aka 'The Brick'
2012 Toyota Prado GX aka 'The Truck'
"Where The Hell is ARDLETHAN!!" :-)
Top
 Profile  
 
Petesmini
 Post subject:
PostPosted: Sun Jun 19, 2011 5:46 pm 
Offline
848cc
848cc

Joined: Sun May 29, 2011 4:07 pm
Posts: 53
Location: Ardlethan, NSW
thomas_hb wrote:
Quote:
Already did that, It drops back to zero Confused


Try the other spade?? If it shoots to 8K it means you've connected it directly to a constant positive.



There is no other spade terminal.

:) Pete

_________________
December 1976 Leyland Mini S aka 'The Brick'
2012 Toyota Prado GX aka 'The Truck'
"Where The Hell is ARDLETHAN!!" :-)
Top
 Profile  
 
thomas_hb
 Post subject:
PostPosted: Sun Jun 19, 2011 5:47 pm 
Offline
998cc
998cc
User avatar

Joined: Fri Feb 18, 2011 4:21 pm
Posts: 644
Location: Sydney, NSW
:? :? :?

Anyone else? I'm stumped.
Top
 Profile  
 
Petesmini
 Post subject:
PostPosted: Sun Jun 19, 2011 5:47 pm 
Offline
848cc
848cc

Joined: Sun May 29, 2011 4:07 pm
Posts: 53
Location: Ardlethan, NSW
Guys,

I'm gonna go get my mini wiring book & have a look at for a moment

Cheers Pete

_________________
December 1976 Leyland Mini S aka 'The Brick'
2012 Toyota Prado GX aka 'The Truck'
"Where The Hell is ARDLETHAN!!" :-)
Top
 Profile  
 
Morris 1100
 Post subject:
PostPosted: Sun Jun 19, 2011 5:59 pm 
Offline
Causing or creating vexation

Joined: Wed Jul 21, 2004 10:32 pm
Posts: 19124
Petesmini wrote:
thomas_hb wrote:
Quote:
Already did that, It drops back to zero Confused


Try the other spade?? If it shoots to 8K it means you've connected it directly to a constant positive.



There is no other spade terminal.

:) Pete

The spade that the tacho is hooked to the coil, is it positive + or negative - ?
Top
 Profile  
 
Petesmini
 Post subject:
PostPosted: Sun Jun 19, 2011 6:06 pm 
Offline
848cc
848cc

Joined: Sun May 29, 2011 4:07 pm
Posts: 53
Location: Ardlethan, NSW
Morris 1100 wrote:
Petesmini wrote:
thomas_hb wrote:
Quote:
Already did that, It drops back to zero Confused


Try the other spade?? If it shoots to 8K it means you've connected it directly to a constant positive.



There is no other spade terminal.

:) Pete

The spade that the tacho is hooked to the coil, is it positive + or negative - ?


Morris 1100,

The best answer to that question is..., with the engine running, I removed the white wire with black trace from the coil & the engine stopped! Tacho drops to nothing, does that tell you if its pos+ or neg-. :)

Pete :)

_________________
December 1976 Leyland Mini S aka 'The Brick'
2012 Toyota Prado GX aka 'The Truck'
"Where The Hell is ARDLETHAN!!" :-)
Top
 Profile  
 
Petesmini
 Post subject: Problem with Tacho!!!
PostPosted: Sun Jun 19, 2011 6:55 pm 
Offline
848cc
848cc

Joined: Sun May 29, 2011 4:07 pm
Posts: 53
Location: Ardlethan, NSW
Petesmini wrote:
Ok folks, just to let you all know the Headlight Upgrade is completed. 'The Brick' now has wipac quadoptics lights installed..., & in case you are all wondering, They work very well! :D I also replaced the voltage stabliser behind the instument console. The fuel gauge & temp work now as well.

The Tacho was not connected up, so I hooked it up as well.However there is a problem with the Tacho reading 8000 rpm as soon as ignition key is turned to Aux or Ign positions. :o

The Tacho is wired in the following way...... Red wire with female spade terminal to male spade terminal, printed circuit circle hole screwed down, white wire with black trace that has a female bullet terminal is connected to male bullet terminal.

So the big question is What the Hell is going on? Any ideas? :oops:


Have moved this Tacho problem to a seperate/new topic.

_________________
December 1976 Leyland Mini S aka 'The Brick'
2012 Toyota Prado GX aka 'The Truck'
"Where The Hell is ARDLETHAN!!" :-)
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 2 of 2
  [ 24 posts ]  Go to page Previous  1, 2

Board index » Mini Chat » Mini Chat

All times are UTC + 10 hours


Who is online

Users browsing this forum: No registered users and 221 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  

© 2016 Ausmini. All garage work involves equal measures of enthusiasm, ingenuity and a fair degree of irresponsibility.