Ausmini
It is currently Thu Jul 24, 2025 5:54 am

Board index » Mini Chat » Mini Chat

All times are UTC + 10 hours




Post new topic Reply to topic  Page 2 of 2
  [ 19 posts ]  Go to page Previous  1, 2
  Print view Previous topic | Next topic 
Author Message
drmini in aust
 Post subject:
PostPosted: Thu Apr 04, 2013 9:53 pm 
Offline
religious status
religious status
User avatar

Joined: Fri Mar 19, 2004 6:19 pm
Posts: 39756
Location: near Baulkham Hills, NSW
John Smidt wrote:
drmini in aust wrote:
@lmbm,
Geez, those hardness numbers of yours seem low!:shock: Have you calibrated the machine lately?

I tested a Karcraft comp one and a Heritage MG 4 synchro one last year, both were between 61-63HRC.

.

Doc If I send You one of My Layshafts and a Diff pin could You do a hardness test on them for Me Please


No problem John. I have access to two Rockwell testers in different places. :wink:

_________________
DrMini- 1970 wasaMatic 1360, Mk1S crank, 86.6HP (ATW) =~125 @ crank, 45 Dellorto (38 chokes), RE282 sprint cam, 1.5 rockers, 11.0:1 C/R. :mrgreen:
Top
 Profile  
 
John Smidt
 Post subject:
PostPosted: Fri Apr 05, 2013 7:02 am 
Offline
The Mini King
User avatar

Joined: Mon May 21, 2007 7:20 pm
Posts: 1338
Location: Windsor, NSW
Thank You very Much Kev, I will get them to You

_________________
" A Hundred Years From Now It will not Matter what my Bank Acount Was,
The Sort Of House I Lived in, Or The Kind Of Car I drove ... But The World May Be A Better Place
Because I was Once Important In The Life Of A Child"
Top
 Profile  
 
GT mowog
 Post subject:
PostPosted: Fri Apr 05, 2013 12:28 pm 
Offline
Mods rock!
User avatar

Joined: Fri Oct 03, 2008 9:02 pm
Posts: 5079
lmbm wrote:
Once i managed to do to some hardness tests on few layshafts, below the results,
i'd say you will be fine with a good second hand A+ layshaft, they seldom wear.

- new pre A+ Australian MG Heritage layshaft 43 HRC ( sourced in 2008 )
- new Minispares A+ competition layshaft 43 HRC ( sourced in 2008 )
- used factory A+ layshaft from low milleage metro 51 HRC
- used factory layshaft from high milleage 4 synchro remote box 52 HRC
- new old stock pre A+ 4 synchro layshaft 55HRC

cheers
Luis


That's close to what I got too, however surface hardness is one thing but if the hardness layer is only a shell ie no depth, then then it won't matter how hard the surface is, the shaft will fail, ruining everything that runs on it. I gave up a while ago trying to find decent layshafts.

_________________
Image
Top
 Profile  
 
John Smidt
 Post subject:
PostPosted: Sat Apr 06, 2013 3:28 pm 
Offline
The Mini King
User avatar

Joined: Mon May 21, 2007 7:20 pm
Posts: 1338
Location: Windsor, NSW
MattE wrote:
Bit of an update:
KC don't have stock of A+ ones for up to a week. If they did have stock, it wouldn't be the same material as their pre A+ ones.
Heritage MG and Mini King don't have the A+ ones either.
I've ordered a hardened EN36 one from MED in UK on Graham Russell's advice - thanks for your time on the phone Graham. A reasonable 46UKP.

Thanks again for the help.
Matt

Mini King are waiting for next batch of Aust Made EN36 stepped Layshafts
We do have EN36 4speed Sync layshafts in stock

_________________
" A Hundred Years From Now It will not Matter what my Bank Acount Was,
The Sort Of House I Lived in, Or The Kind Of Car I drove ... But The World May Be A Better Place
Because I was Once Important In The Life Of A Child"
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 2 of 2
  [ 19 posts ]  Go to page Previous  1, 2

Board index » Mini Chat » Mini Chat

All times are UTC + 10 hours


Who is online

Users browsing this forum: No registered users and 114 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  

cron

© 2016 Ausmini. All garage work involves equal measures of enthusiasm, ingenuity and a fair degree of irresponsibility.