Ausmini
It is currently Sat Jul 19, 2025 12:59 am

Board index » Mini Chat » Mini Chat

All times are UTC + 10 hours




Post new topic Reply to topic  Page 2 of 2
  [ 20 posts ]  Go to page Previous  1, 2
  Print view Previous topic | Next topic 
Author Message
GT1360
 Post subject:
PostPosted: Sat Aug 06, 2005 7:34 pm 
Offline
Postally Verbose
Postally Verbose
User avatar

Joined: Thu Mar 17, 2005 12:58 pm
Posts: 5748
Location: Richmond.... NSW
Gadgets mini wrote:
Just get Little williy to do it for ya he is pretty good at f@#%&*g exhausts

or he could just use that big right arm of his


PMSL... :lol: :lol:
Top
 Profile  
 
drmini in aust
 Post subject:
PostPosted: Sat Aug 06, 2005 7:39 pm 
Offline
religious status
religious status
User avatar

Joined: Fri Mar 19, 2004 6:19 pm
Posts: 39754
Location: near Baulkham Hills, NSW
F*** it- just take a 115mm angle grinder, fit a 1mm thick cutting disc, & cut the sucker off!
You can always weld it (or another bit of pipe) back on, that's what MIG is for. 8)

_________________
DrMini- 1970 wasaMatic 1360, Mk1S crank, 86.6HP (ATW) =~125 @ crank, 45 Dellorto (38 chokes), RE282 sprint cam, 1.5 rockers, 11.0:1 C/R. :mrgreen:
Top
 Profile  
 
willy
 Post subject:
PostPosted: Sat Aug 06, 2005 8:05 pm 
Offline
1360cc
1360cc

Joined: Mon May 03, 2004 6:46 pm
Posts: 13688
Location: ADL
Gadgets mini wrote:
Just get Little williy to do it for ya he is pretty good at f@#%&*g exhausts

or he could just use that big right arm of his



Big, low mufflers... not a worry.
Extractors?? nah pay me and then i might consider doing it.

Right arm? You must know a lot about this, mate???
Top
 Profile  
 
Gadgets mini
 Post subject:
PostPosted: Sat Aug 06, 2005 11:07 pm 
Offline
Resident Haemorrhoid
User avatar

Joined: Mon Jan 31, 2005 7:47 pm
Posts: 6815
Location: in da ACT
big willy wrote:
Gadgets mini wrote:
Just get Little williy to do it for ya he is pretty good at f@#%&*g exhausts

or he could just use that big right arm of his



Big, low mufflers... not a worry.
Extractors?? nah pay me and then i might consider doing it.

Right arm? You must know a lot about this, mate???

Is that the best you can do lil willy??????.........Disappointing lol

_________________
mtsmini wrote:
Master, you are wise beyond your years.....I am a mere grasshopper before you :D

Tombo wrote:
Gadgets has never been so right :D
Top
 Profile  
 
Mike
 Post subject:
PostPosted: Mon Aug 08, 2005 9:45 am 
Offline
1098cc
1098cc
User avatar

Joined: Tue Mar 16, 2004 10:39 pm
Posts: 1629
Location: Sydney, E. Burbs
Try and use a block of wood and a hammer - just knock the y piece back by hitting its edges back gradualy on both sides.
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 2 of 2
  [ 20 posts ]  Go to page Previous  1, 2

Board index » Mini Chat » Mini Chat

All times are UTC + 10 hours


Who is online

Users browsing this forum: No registered users and 103 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  

© 2016 Ausmini. All garage work involves equal measures of enthusiasm, ingenuity and a fair degree of irresponsibility.