ausmini • View topic - Flywheel puller

Board index » Mini Chat » Mini Chat

All times are UTC + 10 hours

Flywheel puller

Moderators: winabbey, simon k, poeee, Mick

Page 1 of 1

[ 11 posts ]

Print view

Previous topic | Next topic

Author

Message

sean

Post subject: Flywheel puller

Posted: Tue Apr 19, 2005 10:11 pm

848cc

Joined: Thu Jan 20, 2005 1:22 am
Posts: 267
Location: Perth

Anyone know if the universal type flywheel puller (sold in Supercheap) will do for a mini flywheel ?

_________________
1977 Clubman

Top

drmini in aust

Post subject:

Posted: Tue Apr 19, 2005 10:48 pm

religious status

Joined: Fri Mar 19, 2004 6:19 pm
Posts: 39755
Location: near Baulkham Hills, NSW

If it's similar to the universal harmonic balance puller, then NO.
It takes TONS of force to pull a Mini flywheel off its taper (usually).
Mine is 20mm thick plate, with a 1" UNF bolt and welded nut, and 3 Grade 8 bolts.
Many Mini flywheel pullers I've seen are just toys..! :lol:

_________________
DrMini- 1970 wasaMatic 1360, Mk1S crank, 86.6HP (ATW) =~125 @ crank, 45 Dellorto (38 chokes), RE282 sprint cam, 1.5 rockers, 11.0:1 C/R. :mrgreen:

Top

sean

Post subject:

Posted: Tue Apr 19, 2005 10:55 pm

848cc

Joined: Thu Jan 20, 2005 1:22 am
Posts: 267
Location: Perth

Yes it is the one you mentioned. Is it worth a go though cos i've got one and need to do the clutch tommorow.

_________________
1977 Clubman

Top

9YaTaH

Post subject: do a search...

Posted: Tue Apr 19, 2005 11:38 pm

1360cc

Joined: Sun Apr 11, 2004 11:32 am
Posts: 12390
Location: Sthrn HiLoLands, NSW, Australia

sean wrote:

Yes it is the one you mentioned. Is it worth a go though cos i've got one and need to do the clutch tommorow.

Sean...do a search here on flywheel and be careful...they can let go with a bang and fly off on an unsuspecting foot etc

_________________
"Show me the Mini!"

Top

supercharged 850

Post subject:

Posted: Wed Apr 20, 2005 2:47 am

1275cc

Joined: Wed Mar 17, 2004 12:16 am
Posts: 5717
Location: Adelaide SA Ausmini Sales Department

sean, if that puller is a bronze/goldy colour "Y" shaped thing.... youre gonna get mad.... I believe it is 5mm too short in each direction. It just_wont_fit.

6mm steel plate just bends like plastic - been there, done that.

Find some 20mm plating as doc says.... its the only safe way.

_________________
[NATHAN] -- Sold everything mini related and am back in big beautiful BMWs

Top

sean

Post subject:

Posted: Wed Apr 20, 2005 7:16 pm

848cc

Joined: Thu Jan 20, 2005 1:22 am
Posts: 267
Location: Perth

No the puller is too small so am hiring one from Minicraft (Perth). have got it all to bits up to pulling the flywheel off. just one question, It says make sure the groove is in the horizontal position on the crankshaft, but I can't see this, only a big slot accross the centre of the flywheel, I have loosened the flywheel nut, i am concerned about the horizontal position issue cos i have heard it is bad if you get it wrong, Hope this all makes sense ?

_________________
1977 Clubman

Top

drmini in aust

Post subject:

Posted: Wed Apr 20, 2005 7:20 pm

religious status

Joined: Fri Mar 19, 2004 6:19 pm
Posts: 39755
Location: near Baulkham Hills, NSW

Put it at TDC on #1 cylinder if you must.... :wink:

BTW it is all bull these days- the early flywheels (pre-`63) had an oil seal in them, and the C-washer could fall in and jam. Since 1963 there is nothing there, no seal.. so it doesn't matter. But countless reprints of workshop manuals continue to mention it. :lol:

_________________
DrMini- 1970 wasaMatic 1360, Mk1S crank, 86.6HP (ATW) =~125 @ crank, 45 Dellorto (38 chokes), RE282 sprint cam, 1.5 rockers, 11.0:1 C/R. :mrgreen:

Top

sean

Post subject:

Posted: Wed Apr 20, 2005 7:23 pm

848cc

Joined: Thu Jan 20, 2005 1:22 am
Posts: 267
Location: Perth

Thanks for the quick reply !, so i should be ok to just pull it off then ?

Put it at TDC on #1 cylinder - what does this mean and how do I do it ?

Sean

_________________
1977 Clubman

Top

Flying Brick

Post subject:

Posted: Wed Apr 20, 2005 7:32 pm

848cc

Joined: Mon Apr 11, 2005 1:18 pm
Posts: 227
Location: Canberra ACT

I have a puller made from the middle of a 2 piece mini flywheel, it's a bit agricultural but it is very strong and works fine. But as mentioned before they can come off with a bang. If you are desperate a strong bit of wood and a big hammer thru the starter motor hole work ok, just need to rotate the crankshaft every couple of hits.
Always wondered why you had to put the slot horizontal, now i know, thanks Dr.
Steve

Top

sean

Post subject:

Posted: Wed Apr 20, 2005 7:44 pm

848cc

Joined: Thu Jan 20, 2005 1:22 am
Posts: 267
Location: Perth

I suppose it is worth changing the engine mount on that side while I am at it ?
How can i tell if the old one is ok or not ?

_________________
1977 Clubman

Top

drmini in aust

Post subject:

Posted: Wed Apr 20, 2005 7:53 pm

religious status

Joined: Fri Mar 19, 2004 6:19 pm
Posts: 39755
Location: near Baulkham Hills, NSW

sean wrote:

Thanks for the quick reply !, so i should be ok to just pull it off then ? YES

Put it at TDC on #1 cylinder - what does this mean and how do I do it ?
Take out No 1 spark plug.
Turn the engine over (put in 4th gear and push) until piston is at top of bore (TDC= Top Dead Centre) check by poking a Biro or pencil or whatever down the plug hole.
No you don't need to...
Sean

_________________
DrMini- 1970 wasaMatic 1360, Mk1S crank, 86.6HP (ATW) =~125 @ crank, 45 Dellorto (38 chokes), RE282 sprint cam, 1.5 rockers, 11.0:1 C/R. :mrgreen:

Top

Page 1 of 1

[ 11 posts ]

Board index » Mini Chat » Mini Chat

All times are UTC + 10 hours

Who is online

Users browsing this forum: No registered users and 93 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to: