i won a ignition barrel on ebay as mine is broke

http://cgi.ebay.com.au/ws/eBayISAPI.dll ... 4543613690

how do i take the one off my car the screws are just flat on the top, do i just drill em out? and where eould i get new ones from or is there a special way to get them out

hellllllp

_________________
1152cc turbo A-series now with 125.7hp at the wheels !

AUSSIE Turbo mini forum >> http://boostmini.justboard.net/

https://www.facebook.com/boostmini

Drill small diameter holes down the middle of the shear bolts and then use "easy-outs" or similar. replace with normal fasteners when re-building.

Drill em out or if your impatient Angle grinder with a cutting disc. When you get it, take it to a bolt place and pick up two with the right length and thread. Easy

Cheers

Aaron

_________________

so you cant get the same bolts again or get the same sort? cant someone steal the car if i use normal bolts?

_________________
1152cc turbo A-series now with 125.7hp at the wheels !

AUSSIE Turbo mini forum >> http://boostmini.justboard.net/

https://www.facebook.com/boostmini

If your worried about someone stealing your car, you should be worried as mini's are so easy to break into and start. If your worried about that kind of thing, put a cut out switch in with a removable toggle.

Cheers

Aaron

_________________

naa im not worried just wondering if you can get the original bolts

_________________
1152cc turbo A-series now with 125.7hp at the wheels !

AUSSIE Turbo mini forum >> http://boostmini.justboard.net/

https://www.facebook.com/boostmini

Get two ordinary bolts and neck them down in a lathe the same as the originals. Use a centre punch to get them out, at least that is what I have done in the past with no problems.

_________________
Chris

Everything I like is either
illegal, immoral or fattening.

Doubtful, but you can try. Bolt specialsts are your only hope really.

Cheers

Aaron

_________________

If you are good you can undo them with a hammer and a punch.
If you have a Dremmel you can cut a slot in them and use a screwdriver.

If you cut a slot in them you can fill the slot with araldite after you do them up again. Only you will know what is under the araldite.

i have a steering collum with the barrle and key intact so all ya gotta do is change the collum 50 and it is yours
makka

_________________
Anonymous moderation means the agro that is built up towards the mods isn't aimed at an individual (fewer "Makk" attacks). Less stress for mods means less moderator "retirements".

mmmm, ill keep it in mind if this becomes too hard thanks for the offer

_________________
1152cc turbo A-series now with 125.7hp at the wheels !

AUSSIE Turbo mini forum >> http://boostmini.justboard.net/

https://www.facebook.com/boostmini

ok i got it all in but when i turn it to start nothing happens. ok befor i put it in i had a button that i pressed so i unwired all that and wired the ignition barrel back in when you turn the key the dash lights come on but it wont start any ideas?? there was a wire in the engine bay infront of the starter motor that used to go to the button and back to that thng with the fat wire going to it next to the head and engine steady, i touch the wire on the front of this and the starter motor tured hellllp how do i fix

_________________
1152cc turbo A-series now with 125.7hp at the wheels !

AUSSIE Turbo mini forum >> http://boostmini.justboard.net/

https://www.facebook.com/boostmini

heres a pic, the thing above the coil what wires are meant to go on the things circled

_________________
1152cc turbo A-series now with 125.7hp at the wheels !

AUSSIE Turbo mini forum >> http://boostmini.justboard.net/

https://www.facebook.com/boostmini