Ausmini
It is currently Tue Jul 22, 2025 6:00 pm

Board index » Mini Chat » Mini Chat

All times are UTC + 10 hours




Post new topic Reply to topic  Page 1 of 1
  [ 9 posts ] 
  Print view Previous topic | Next topic 
Author Message
nathanm
PostPosted: Fri Dec 15, 2006 8:54 pm 
Offline
998cc
998cc
User avatar

Joined: Sat Jun 24, 2006 6:23 pm
Posts: 523
Location: melbourne
im trying to bolt the back together and i can tighten it to a certain point but then it starts turning round like you have to hold on to something to stop turnig

so my q. is how do u do this

sorry if this doesnt make much sense im new to this

thanks nathan

_________________
1969 mini k
Top
 Profile  
 
Harley
 Post subject:
PostPosted: Fri Dec 15, 2006 8:59 pm 
Offline
1360cc
1360cc
User avatar

Joined: Mon Aug 23, 2004 10:07 pm
Posts: 10653
Location: SE Melbourne
Provided both parts are paint, dirt and grease free, they should be fine.
some light taps with a fibre hammer may help settle the joints in a bit.
Put some copper grease on the retainer nut too.
:D
Top
 Profile  
 
DOZ
 Post subject:
PostPosted: Fri Dec 15, 2006 9:19 pm 
Offline
1098cc
1098cc
User avatar

Joined: Fri Jan 14, 2005 9:08 pm
Posts: 1683
Location: Bris Vegas Occupation: Engineer
Put some weight on it, ie with the jack under the bottom arm.

Daniel

_________________
Videos - Turbocharged A-Series on Dyno & at Wakefield
Mafs waz not my strong subgeckt at skkol
Top
 Profile  
 
buztoy
 Post subject:
PostPosted: Fri Dec 15, 2006 10:40 pm 
Offline
998cc
998cc
User avatar

Joined: Tue Mar 28, 2006 7:30 pm
Posts: 1184
Location: ASQUITH NSW, Engine size:1310
what he said, jack from underneth act as your hand, i was told to also add a flat washer with a lock washer,

_________________
any parts for a 76 clubby pm me or ring 0405 329 326

http://www.ausmini.com/forums/viewtopic.php?t=44717
Top
 Profile  
 
Rodney
 Post subject:
PostPosted: Sat Dec 16, 2006 10:21 am 
Offline
1275cc
1275cc
User avatar

Joined: Mon Oct 25, 2004 9:52 am
Posts: 2027
Location: Clifton Springs, Victoria
Like they said above - put a jack under and carefully pump it up a bit or the other way is to lower the car down with a length of 4 x 2 (or similar) on its end (of course) under the ball joint.

Happy Chrissy

_________________
Rod Image
http://smg.photobucket.com/albums/v607/Rodney/
Top
 Profile  
 
drmini in aust
 Post subject:
PostPosted: Sat Dec 16, 2006 10:26 am 
Offline
religious status
religious status
User avatar

Joined: Fri Mar 19, 2004 6:19 pm
Posts: 39755
Location: near Baulkham Hills, NSW
buztoy wrote:
what he said, jack from underneth act as your hand, i was told to also add a flat washer with a lock washer,

A lock (spring) washer should not be used with a flat washer. It defeats the purpose of the spring washer... as the flat washer can spin it undone. :wink:

_________________
DrMini- 1970 wasaMatic 1360, Mk1S crank, 86.6HP (ATW) =~125 @ crank, 45 Dellorto (38 chokes), RE282 sprint cam, 1.5 rockers, 11.0:1 C/R. :mrgreen:
Top
 Profile  
 
buztoy
 Post subject:
PostPosted: Sat Dec 16, 2006 10:32 am 
Offline
998cc
998cc
User avatar

Joined: Tue Mar 28, 2006 7:30 pm
Posts: 1184
Location: ASQUITH NSW, Engine size:1310
so i allready have so what should i replace it with

_________________
any parts for a 76 clubby pm me or ring 0405 329 326

http://www.ausmini.com/forums/viewtopic.php?t=44717
Top
 Profile  
 
drmini in aust
 Post subject:
PostPosted: Sat Dec 16, 2006 11:36 am 
Offline
religious status
religious status
User avatar

Joined: Fri Mar 19, 2004 6:19 pm
Posts: 39755
Location: near Baulkham Hills, NSW
A new spring washer... :wink:
The idea of a spring washer is the ends bite in and prevent it unscrewing.
Alternatively, use a Nyloc nut, no washer needed.

_________________
DrMini- 1970 wasaMatic 1360, Mk1S crank, 86.6HP (ATW) =~125 @ crank, 45 Dellorto (38 chokes), RE282 sprint cam, 1.5 rockers, 11.0:1 C/R. :mrgreen:
Top
 Profile  
 
buztoy
 Post subject:
PostPosted: Sat Dec 16, 2006 11:53 am 
Offline
998cc
998cc
User avatar

Joined: Tue Mar 28, 2006 7:30 pm
Posts: 1184
Location: ASQUITH NSW, Engine size:1310
but then it would chew into the rubber or it that ment to happen

_________________
any parts for a 76 clubby pm me or ring 0405 329 326

http://www.ausmini.com/forums/viewtopic.php?t=44717
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 9 posts ] 

Board index » Mini Chat » Mini Chat

All times are UTC + 10 hours


Who is online

Users browsing this forum: No registered users and 80 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  

cron

© 2016 Ausmini. All garage work involves equal measures of enthusiasm, ingenuity and a fair degree of irresponsibility.