Ausmini
It is currently Fri Jul 18, 2025 5:06 pm

Board index » Mini Chat » Mini Chat

All times are UTC + 10 hours




Post new topic Reply to topic  Page 1 of 2
  [ 27 posts ]  Go to page 1, 2  Next
  Print view Previous topic | Next topic 
Author Message
sg
 Post subject: KAD Quickshift Kit
PostPosted: Sun Dec 19, 2004 8:16 pm 
Offline
1275cc
1275cc
User avatar

Joined: Sat Aug 07, 2004 7:51 am
Posts: 2935
Location: Manly West, Brisbane, Qld
Guys, how easy is it to fit a kit to a remote change MK1 gearbox, and what is involved in the process.........

Steve

_________________
I got nuthin......................
Top
 Profile  
 
brickworx
 Post subject:
PostPosted: Sun Dec 19, 2004 8:24 pm 
Offline
1275cc
1275cc
User avatar

Joined: Tue Dec 14, 2004 9:38 am
Posts: 2008
Location: Adelaide, South Australia
Extremely easy, just undo your two gear lever plate bolts from inside,
kit comes with longer bolts.

_________________
Miniworx Centre 0883741299
Sooperdooperminicooperexpertengineering
Online BMW Mini Shop
Top
 Profile  
 
sg
 Post subject:
PostPosted: Sun Dec 19, 2004 8:28 pm 
Offline
1275cc
1275cc
User avatar

Joined: Sat Aug 07, 2004 7:51 am
Posts: 2935
Location: Manly West, Brisbane, Qld
How easy was that!!!!!!!!! cheers for that Mr Brickworx 8)

_________________
I got nuthin......................
Top
 Profile  
 
brickworx
 Post subject:
PostPosted: Sun Dec 19, 2004 8:32 pm 
Offline
1275cc
1275cc
User avatar

Joined: Tue Dec 14, 2004 9:38 am
Posts: 2008
Location: Adelaide, South Australia
When you do the conversion, check the plastic bush on the end of the lever for wear,
chech your selector bolts are tight, wear on bronze bushes and wear in the remote shaft. The better these are... the better the new shifter works

_________________
Miniworx Centre 0883741299
Sooperdooperminicooperexpertengineering
Online BMW Mini Shop
Top
 Profile  
 
sg
 Post subject:
PostPosted: Sun Dec 19, 2004 9:29 pm 
Offline
1275cc
1275cc
User avatar

Joined: Sat Aug 07, 2004 7:51 am
Posts: 2935
Location: Manly West, Brisbane, Qld
Now would i be correct in saying that the ability to select and find the gates will be improved by this???? or not????..... or the aim of the kit is just to improve the throw of the gearshift???? :? :? I am new to all of this and find it a bit confusing

_________________
I got nuthin......................
Top
 Profile  
 
dr trim
 Post subject:
PostPosted: Sun Dec 19, 2004 9:32 pm 
Offline
1275cc
1275cc
User avatar

Joined: Tue Mar 16, 2004 12:38 pm
Posts: 2061
Location: adelaide
i'd also like to know :wink:
doesnt it make the feel for gears alot tighter?
like there's only 1 place u can go, where as mine even when it sits in first it can still be wobbled around
Top
 Profile  
 
drmini in aust
 Post subject:
PostPosted: Sun Dec 19, 2004 9:39 pm 
Offline
religious status
religious status
User avatar

Joined: Fri Mar 19, 2004 6:19 pm
Posts: 39754
Location: near Baulkham Hills, NSW
sg wrote:
Now would i be correct in saying that the ability to select and find the gates will be improved by this???? or not????..... or the aim of the kit is just to improve the throw of the gearshift???? :? :? I am new to all of this and find it a bit confusing

Might be better on a rodchange (which needs it I reckon), but on a remote, there have been reports in US that the gate feel is crap with this conversion.
BTW they should be called a short shift, NOT a quickshift.

Dunno why you would bother on a remote- the shift distance is already about 1/2 what a rodchange is! :lol:

_________________
DrMini- 1970 wasaMatic 1360, Mk1S crank, 86.6HP (ATW) =~125 @ crank, 45 Dellorto (38 chokes), RE282 sprint cam, 1.5 rockers, 11.0:1 C/R. :mrgreen:
Top
 Profile  
 
sg
 Post subject:
PostPosted: Sun Dec 19, 2004 9:40 pm 
Offline
1275cc
1275cc
User avatar

Joined: Sat Aug 07, 2004 7:51 am
Posts: 2935
Location: Manly West, Brisbane, Qld
dr trim wrote:
i'd also like to know :wink:
doesnt it make the feel for gears alot tighter?
like there's only 1 place u can go, where as mine even when it sits in first it can still be wobbled around


Yeah i would like to know that one as well Doc Trim...........

_________________
I got nuthin......................
Top
 Profile  
 
9YaTaH
PostPosted: Sun Dec 19, 2004 9:41 pm 
Offline
1360cc
1360cc
User avatar

Joined: Sun Apr 11, 2004 11:32 am
Posts: 12390
Location: Sthrn HiLoLands, NSW, Australia
sg wrote:
Now would i be correct in saying that the ability to select and find the gates will be improved by this???? or not????..... or the aim of the kit is just to improve the throw of the gearshift???? :? :? I am new to all of this and find it a bit confusing


Don't know about gates...but you certainly shorten the throw...however....
remember. too quick and you will still beat the synchros :roll:

_________________
"Show me the Mini!"
Top
 Profile  
 
willy
 Post subject:
PostPosted: Sun Dec 19, 2004 9:43 pm 
Offline
1360cc
1360cc

Joined: Mon May 03, 2004 6:46 pm
Posts: 13688
Location: ADL
On my rod change, I have the "quick shift" fitted. It is SO much tighter when the gear is selected and there is virtually no movement inside the gear. I would recommend this for sure. Its great...

But... you gotta practice LIFTING for reverse (my selector rod was rooted so i didnt used to have to lift :lol: )

About 10x up and down the driveway gives some good practice for this :wink:
Top
 Profile  
 
drmini in aust
 Post subject:
PostPosted: Sun Dec 19, 2004 9:44 pm 
Offline
religious status
religious status
User avatar

Joined: Fri Mar 19, 2004 6:19 pm
Posts: 39754
Location: near Baulkham Hills, NSW
sg,
The best way to improve the gate lockout on a remote change is chuck the old spring (under a hex plug or reverse switch, near oil filter) and fit a heavier one- a `blue' or `red' die spring.
PM me your address and I'll send you one for Xmas, I prepared previously.. 8)
A few people on here use them - Gafmo has one, also Ozmotorsport. :P

_________________
DrMini- 1970 wasaMatic 1360, Mk1S crank, 86.6HP (ATW) =~125 @ crank, 45 Dellorto (38 chokes), RE282 sprint cam, 1.5 rockers, 11.0:1 C/R. :mrgreen:
Top
 Profile  
 
dr trim
 Post subject:
PostPosted: Sun Dec 19, 2004 10:18 pm 
Offline
1275cc
1275cc
User avatar

Joined: Tue Mar 16, 2004 12:38 pm
Posts: 2061
Location: adelaide
what exactly does that do doc?
and near the oil filter? :shock:
on the same side as the oil filter or opposite?
i've got a remote change aswell. u dont recommend a quickshift?
Top
 Profile  
 
gafmo
 Post subject:
PostPosted: Sun Dec 19, 2004 11:11 pm 
Offline
the King of Bling
User avatar

Joined: Thu Jun 03, 2004 11:11 pm
Posts: 19858
Location: Baulkham Hills
Nar Nar Nar...... :!:
Go the Remot as doc as has mention with the spring...
1st to forth is nice and tight...The big R is a push ti the right with a noice you will get to notices....nice


I am Converted...I have also heard that the quick shift stuffs your sinck's
Do as the Doc has said...I'm pleased and so is the Wife, and that has to be good :idea:

_________________
Stop Licking the Dog...I Don't Care Who Started It
Top
 Profile  
 
drmini in aust
 Post subject:
PostPosted: Mon Dec 20, 2004 5:35 am 
Offline
religious status
religious status
User avatar

Joined: Fri Mar 19, 2004 6:19 pm
Posts: 39754
Location: near Baulkham Hills, NSW
dr trim wrote:
what exactly does that do doc?
and near the oil filter? :shock:
on the same side as the oil filter or opposite?
i've got a remote change aswell. u dont recommend a quickshift?

There is a spring inside the box, just below the oil filter. Its purpose is to block the reverse gate, but it's pretty weak even when new. Over time, the selector rod and lockout plunger get slightly worn and you can hit thru the gate too easy on the 2-3 upshift.
Fitting a stronger spring fixes this. It goes in from outside- easy peasy. :wink:
Watch the length of the spring it's compressed length must be the same as original.

No I don't like quickshifts on remote boxes. These are `quicker' than a rod change to start with. :lol:

_________________
DrMini- 1970 wasaMatic 1360, Mk1S crank, 86.6HP (ATW) =~125 @ crank, 45 Dellorto (38 chokes), RE282 sprint cam, 1.5 rockers, 11.0:1 C/R. :mrgreen:
Top
 Profile  
 
Boostedmini
 Post subject:
PostPosted: Mon Dec 20, 2004 7:47 am 
Offline
998cc
998cc
User avatar

Joined: Thu Sep 23, 2004 2:24 pm
Posts: 1170
Location: Quakers Hill - Only the Hills
Yeah i agree with the Doc, i have a DOC prepared spring and it made a big difference, but i also have the KAD qik shift (remote type) and its not too bad, takes time to get used to and when going hard it can be tricky to get third and also has a tendency to stick in reverse but it is not a bad conversion for the price i paid (nix).

_________________
Image

100% Pure A Series Turbo
Morris - The Original RedBull Racing
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 2
  [ 27 posts ]  Go to page 1, 2  Next

Board index » Mini Chat » Mini Chat

All times are UTC + 10 hours


Who is online

Users browsing this forum: No registered users and 88 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  

cron

© 2016 Ausmini. All garage work involves equal measures of enthusiasm, ingenuity and a fair degree of irresponsibility.