Ausmini
It is currently Sun Jul 27, 2025 2:35 pm

Board index » Mini Chat » Mini Chat

All times are UTC + 10 hours




Post new topic Reply to topic  Page 2 of 2
  [ 27 posts ]  Go to page Previous  1, 2
  Print view Previous topic | Next topic 
Author Message
Morris 1100
 Post subject:
PostPosted: Sat May 24, 2008 9:41 pm 
Offline
Causing or creating vexation

Joined: Wed Jul 21, 2004 10:32 pm
Posts: 19124
BALLISTIC wrote:
Morris 1100 wrote:
A trick that I was taught when I was working in a wrecking yard was to loosten the nut but dont remove it and thump downwards on the outer rim of the steering wheel. You just slap down on both sides in sequence just like bashing the bongo drums. :shock:

It soulds all wrong but it works. I never used a puller on a steering wheel after I learned that trick. :D


Then when pulling towards you wiggle the s/wheel side to side with some force and it should come off the splines quite easily. Also a sqirt of wd40, rp7, inox, etc where the splines are in the centre of the boss may help too.
You don't need to pull, you just slap it downwards quite harshly repeatedly and then lift it off. No need for WD40. I have done it on hundreds of different cars.
Top
 Profile  
 
Mick
 Post subject:
PostPosted: Sat May 24, 2008 9:45 pm 
Offline
SooperDooperMiniCooper ExpertEngineering
User avatar

Joined: Fri Apr 29, 2005 9:46 am
Posts: 18887
Location: Under the bonnet son!
Morris 1100 wrote:
A trick that I was taught when I was working in a wrecking yard was to loosten the nut and thump downwards on the outer rim of the steering wheel. You just slap down on both sides in sequence just like bashing the bongo drums. :shock:

It sounds all wrong but it works. I never used a puller on a steering wheel after I learned that trick. :D


that's a trick I remember being taught in my first year as well. Works on all kinds of applications..

_________________
SooperDooperMiniCooperExpertEngineering

All garage work involves equal measures of enthusiasm, ingenuity and a fair degree of irresponsibility.
Top
 Profile  
 
Sabreatche
 Post subject:
PostPosted: Sat May 24, 2008 9:45 pm 
Offline
848cc
848cc
User avatar

Joined: Mon May 23, 2005 12:11 am
Posts: 72
Location: Sydney, NSW
Done! All it needed was good whallop. Now, please tell me getting the new one on isn't going to be as hard. certainly looks a tight fit. I'm off to work, will have a go in the morning.

_________________
1978 Mini Clubman 998cc...for now
Top
 Profile  
 
Mick
 Post subject:
PostPosted: Sat May 24, 2008 9:47 pm 
Offline
SooperDooperMiniCooper ExpertEngineering
User avatar

Joined: Fri Apr 29, 2005 9:46 am
Posts: 18887
Location: Under the bonnet son!
Cool, the importance of contact counselling in resolving conflicts can never be under estimated.

_________________
SooperDooperMiniCooperExpertEngineering

All garage work involves equal measures of enthusiasm, ingenuity and a fair degree of irresponsibility.
Top
 Profile  
 
Morris 1100
 Post subject:
PostPosted: Sat May 24, 2008 9:49 pm 
Offline
Causing or creating vexation

Joined: Wed Jul 21, 2004 10:32 pm
Posts: 19124
Mick wrote:
Morris 1100 wrote:
A trick that I was taught when I was working in a wrecking yard was to loosten the nut and thump downwards on the outer rim of the steering wheel. You just slap down on both sides in sequence just like bashing the bongo drums. :shock:

It sounds all wrong but it works. I never used a puller on a steering wheel after I learned that trick. :D


that's a trick I remember being taught in my first year as well. Works on all kinds of applications..
Tapers and tapered splines hold very well against a direct pull or rotation, that is why they use them in these applications.
But a knock the wrong way seems to confuse them. :lol:
Top
 Profile  
 
Mick
 Post subject:
PostPosted: Sat May 24, 2008 10:20 pm 
Offline
SooperDooperMiniCooper ExpertEngineering
User avatar

Joined: Fri Apr 29, 2005 9:46 am
Posts: 18887
Location: Under the bonnet son!
When pullers weren't available, by knocking the shaft with a copper hammer you could get the bearing or whatever it was to 'walk' up toward you. It used to baffle me at the time, but I didn't care if it made the day a little easier..

It didn't work every time, but the ingenuity and general dodgy techniques would then come to the fore in removing the stubborn so and so.

_________________
SooperDooperMiniCooperExpertEngineering

All garage work involves equal measures of enthusiasm, ingenuity and a fair degree of irresponsibility.
Top
 Profile  
 
Sabreatche
 Post subject:
PostPosted: Sun May 25, 2008 2:59 pm 
Offline
848cc
848cc
User avatar

Joined: Mon May 23, 2005 12:11 am
Posts: 72
Location: Sydney, NSW
-Sigh- The saga continues.

Despite thousands of assurances from the kid at AutoOne, the boss kit he gave me (free, I might add, so not complaining too loudly here) for the wheel I purchased is too small, the spindle size is off, not by a lot, but still a good millimetre or so, and after a lot of loud banging all I am achieving is slowly flattening the centre bolt thread. I don't suppose anyone knows the specific measurements for the spindle on a Clubbie? Should I be hunting down something mini specific, or should I be able to grab a generic boss no worries?

_________________
1978 Mini Clubman 998cc...for now
Top
 Profile  
 
DOZ
 Post subject:
PostPosted: Sun May 25, 2008 3:03 pm 
Offline
1098cc
1098cc
User avatar

Joined: Fri Jan 14, 2005 9:08 pm
Posts: 1683
Location: Bris Vegas Occupation: Engineer
Sabreatche wrote:
Despite thousands of assurances from the kid at AutoOne


I think you answered your own question there. The boss kit must be made for a Mini to be safe.

Have you got the old boss off yet?

Daniel

_________________
Videos - Turbocharged A-Series on Dyno & at Wakefield
Mafs waz not my strong subgeckt at skkol
Top
 Profile  
 
1018cc
 Post subject:
PostPosted: Sun May 25, 2008 3:37 pm 
Offline
Give Ash some flowers Nick .
User avatar

Joined: Wed Aug 09, 2006 1:22 pm
Posts: 10149
Location: Toowoomba Region, QLD
What ever you do - please don't damage the spline!

Take the boss back and get one to suit a mini. Don't wreck the steering.

_________________
"In two years time your car will be like a lady's clothes, out of date, my car will still be in fashion when I am dead" - Sir Alec speaking to Pininfarina
Top
 Profile  
 
Hanra
 Post subject:
PostPosted: Sun May 25, 2008 3:50 pm 
Offline
1360cc
1360cc
User avatar

Joined: Sat May 08, 2004 9:01 pm
Posts: 6844
Location: Cairns, Nrth QLD
My SAAS boss kit was specific for mini and was about $80 10yrs ago.

_________________
Image
http://www.youtube.com/user/Hanras
Top
 Profile  
 
Sabreatche
 Post subject:
PostPosted: Sun May 25, 2008 4:23 pm 
Offline
848cc
848cc
User avatar

Joined: Mon May 23, 2005 12:11 am
Posts: 72
Location: Sydney, NSW
Hanra, yeah my wheel is an SAAS, just need to hunt down a mini boss now.

_________________
1978 Mini Clubman 998cc...for now
Top
 Profile  
 
Hanra
 Post subject:
PostPosted: Sun May 25, 2008 4:35 pm 
Offline
1360cc
1360cc
User avatar

Joined: Sat May 08, 2004 9:01 pm
Posts: 6844
Location: Cairns, Nrth QLD
I got mine from Ricebarn back in the day. Im sure they can order one in?

_________________
Image
http://www.youtube.com/user/Hanras
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 2 of 2
  [ 27 posts ]  Go to page Previous  1, 2

Board index » Mini Chat » Mini Chat

All times are UTC + 10 hours


Who is online

Users browsing this forum: No registered users and 93 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  

© 2016 Ausmini. All garage work involves equal measures of enthusiasm, ingenuity and a fair degree of irresponsibility.