Ausmini
It is currently Sun Jul 27, 2025 8:36 pm

Board index » Mini Chat » Mini Chat

All times are UTC + 10 hours




Post new topic Reply to topic  Page 1 of 2
  [ 22 posts ]  Go to page 1, 2  Next
  Print view Previous topic | Next topic 
Author Message
gafmo
 Post subject: Water Pump
PostPosted: Mon Apr 04, 2005 11:20 pm 
Offline
the King of Bling
User avatar

Joined: Thu Jun 03, 2004 11:11 pm
Posts: 19858
Location: Baulkham Hills
When is it not working.
I have changed the thermostat (74), Flushed the System (including the Heater), Ensured no Airpockets in the head.
Still heats to half realy quickly and goes to High and stays thier...
Other than that could it be the bottom radiator hose contracting :roll:
I have also done the Bushies Compretion test all fine thier also

_________________
Stop Licking the Dog...I Don't Care Who Started It
Top
 Profile  
 
drmini in aust
 Post subject:
PostPosted: Mon Apr 04, 2005 11:21 pm 
Offline
religious status
religious status
User avatar

Joined: Fri Mar 19, 2004 6:19 pm
Posts: 39757
Location: near Baulkham Hills, NSW
Checked the timing? Might be retarded...:wink:

_________________
DrMini- 1970 wasaMatic 1360, Mk1S crank, 86.6HP (ATW) =~125 @ crank, 45 Dellorto (38 chokes), RE282 sprint cam, 1.5 rockers, 11.0:1 C/R. :mrgreen:
Top
 Profile  
 
gafmo
 Post subject:
PostPosted: Mon Apr 04, 2005 11:25 pm 
Offline
the King of Bling
User avatar

Joined: Thu Jun 03, 2004 11:11 pm
Posts: 19858
Location: Baulkham Hills
We did that :?

_________________
Stop Licking the Dog...I Don't Care Who Started It
Top
 Profile  
 
1310/71
 Post subject:
PostPosted: Mon Apr 04, 2005 11:41 pm 
Offline
1275cc
1275cc

Joined: Mon Mar 22, 2004 7:41 pm
Posts: 4319
Location: Plumpton, NSW
How worn is the pump likely to be? I have heard of some pumps cavitating when worn. When was the last time you spun it - was the bearing OK? (usually do this off the car however)

The hi-flow pumps are about $70 at Karcraft I think.

Other than that, even though you flushed the rad, is it time to consider pulling it out for a service?

KB
Top
 Profile  
 
gafmo
 Post subject:
PostPosted: Tue Apr 05, 2005 6:38 am 
Offline
the King of Bling
User avatar

Joined: Thu Jun 03, 2004 11:11 pm
Posts: 19858
Location: Baulkham Hills
I hate pulling the Rad out but I guess I could Marcia (The Donner) hers and see how the goes. I may as well pull the water pump off as well then :roll:

_________________
Stop Licking the Dog...I Don't Care Who Started It
Top
 Profile  
 
J_A_M
 Post subject:
PostPosted: Tue Apr 05, 2005 8:54 am 
Offline
1360cc
1360cc

Joined: Tue Mar 16, 2004 11:32 am
Posts: 9068
whats your rad like? how old is it?

Might need a flush out of the car, or top and bottom tanks off for a core clean.

My clubby rad looks like it was replaced recently....nice and new....but I am taking it to a rad place for a pressure flush. :P
Top
 Profile  
 
Matt68
 Post subject:
PostPosted: Tue Apr 05, 2005 9:01 am 
Offline
1275cc
1275cc
User avatar

Joined: Thu Mar 18, 2004 1:33 pm
Posts: 2213
Location: Darling Downs QLD
I had similar overheating problems in my deluxe, checked everything, flushed system out a lot, cores all looked clean but nothing worked.

In the end I took it to my local radiator works and he took the tanks off for a core clean.
About 40% of the cores were completely blocked, you just couldn't tell with the tank on!

Recored rad & now it's sweet as.

Cheers & good luck

Matt
Top
 Profile  
 
J_A_M
 Post subject:
PostPosted: Tue Apr 05, 2005 9:45 am 
Offline
1360cc
1360cc

Joined: Tue Mar 16, 2004 11:32 am
Posts: 9068
Matt, I agree 110%. I have seen guys do this on a rad, and it's amazing how much sh!t comes out.

Jim, I am getting mine done soon....lets take both there and push for a discount! :D
Top
 Profile  
 
redfive
 Post subject:
PostPosted: Tue Apr 05, 2005 10:53 am 
Offline
848cc
848cc
User avatar

Joined: Tue Mar 23, 2004 7:52 pm
Posts: 314
Location: Adelaide, South Australia
A lot of my overheating issues were due to the temp guage being out :oops:.

New radiator, hoses and water pump before I worked that out.
Top
 Profile  
 
danidad
 Post subject:
PostPosted: Tue Apr 05, 2005 11:59 am 
Offline
1098cc
1098cc
User avatar

Joined: Sat Oct 16, 2004 10:59 pm
Posts: 1285
Location: the Cold Toast QLD
that would anoy me redfive hate it when things like that happen.

_________________
No longer Ms Westwoods mini outside her original kings road shop
Top
 Profile  
 
gafmo
 Post subject:
PostPosted: Tue Apr 05, 2005 5:25 pm 
Offline
the King of Bling
User avatar

Joined: Thu Jun 03, 2004 11:11 pm
Posts: 19858
Location: Baulkham Hills
We'll the Rad is around 2 - 3 years 2 core special from Karcraft
How Much does it cost..(only asking as they will be shut by now :?
But I'll call around tomorrow as I have the day off, Wify is going for her First Little Gafmo check 8)
I was hoping to pop into Karcraft tomorrow for some bits for Marcia While we were out..Hopeing Sue will be in a good mood and I can spend a few dollars :lol:

Anyway I degre's I also have two other rad's and a few Heater rads + plus a oil cooler...Bulk job may work..(srug of the shoulders)

_________________
Stop Licking the Dog...I Don't Care Who Started It
Top
 Profile  
 
drmini in aust
 Post subject:
PostPosted: Tue Apr 05, 2005 10:27 pm 
Offline
religious status
religious status
User avatar

Joined: Fri Mar 19, 2004 6:19 pm
Posts: 39757
Location: near Baulkham Hills, NSW
You did run plain water in it for quite a while, the rad core might be coated in crud...
What pump is it? I've seen them with cast iron impellers (good), plastic impellers (??), & bent tin impellers (crap)..!

_________________
DrMini- 1970 wasaMatic 1360, Mk1S crank, 86.6HP (ATW) =~125 @ crank, 45 Dellorto (38 chokes), RE282 sprint cam, 1.5 rockers, 11.0:1 C/R. :mrgreen:
Top
 Profile  
 
gafmo
 Post subject:
PostPosted: Tue Apr 05, 2005 10:51 pm 
Offline
the King of Bling
User avatar

Joined: Thu Jun 03, 2004 11:11 pm
Posts: 19858
Location: Baulkham Hills
drmini in aust wrote:
You did run plain water in it for quite a while, the rad core might be coated in crud...
What pump is it? I've seen them with cast iron impellers (good), plastic impellers (??), & bent tin impellers (crap)..!

Mate, no Idea what the Pump Looks Like.....Can't even say I even had a look at it what we rebuilt the motor.. :?
Intentiion tomorrow..Fine someone to do over one of my spares and put it in...Then redo Morris's old one and put it into Marcia :idea:
If all goes well I will not touch it..But if it fails it's the pump newbie
Sue's has said the Fan belt is slipping..but I have driven Morris in the last couple of weeks and have not notice to much skwealling

_________________
Stop Licking the Dog...I Don't Care Who Started It
Top
 Profile  
 
gafmo
 Post subject:
PostPosted: Wed Apr 06, 2005 3:44 pm 
Offline
the King of Bling
User avatar

Joined: Thu Jun 03, 2004 11:11 pm
Posts: 19858
Location: Baulkham Hills
$95 to rip the tanks off and rod them.
$40 for Heater cores and $30 for a Oil cooler to be cemicaly diped
And no discount if all together and a total 3 Radiators

I thought it was goi9ng to cheaper than that :x

_________________
Stop Licking the Dog...I Don't Care Who Started It
Top
 Profile  
 
J_A_M
 Post subject:
PostPosted: Wed Apr 06, 2005 3:51 pm 
Offline
1360cc
1360cc

Joined: Tue Mar 16, 2004 11:32 am
Posts: 9068
where from?.... I was expecting $90 for the rad clean....
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 2
  [ 22 posts ]  Go to page 1, 2  Next

Board index » Mini Chat » Mini Chat

All times are UTC + 10 hours


Who is online

Users browsing this forum: fuzzy-hair-man, Goldbrocade_62 and 91 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  

© 2016 Ausmini. All garage work involves equal measures of enthusiasm, ingenuity and a fair degree of irresponsibility.