Ausmini
It is currently Sat Jul 19, 2025 4:47 pm

Board index » Mini Chat » Mini Chat

All times are UTC + 10 hours




Post new topic Reply to topic  Page 2 of 3
  [ 39 posts ]  Go to page Previous  1, 2, 3  Next
  Print view Previous topic | Next topic 
Author Message
dalmeny
 Post subject: Re: What's going on????
PostPosted: Sun Nov 06, 2011 11:53 am 
Offline
848cc
848cc
User avatar

Joined: Fri Jul 01, 2011 3:20 pm
Posts: 460
Location: Goulburn NSW
miniDave wrote:
dalmeny wrote:
2. The cover plates over the push rods, fitted with cork caskets and good sealant were leaking oil down the back of the engine. I had them a nice snug tight, but obviously not tight enough. Can you tighten the bejessus out of those cork gaskets??????


If your covers are the ones that rise outwards with the bolt on the peak then you need to seal around the bolt head. There is a rubber/felt washer as new but I put some RTV Grey gasket maker under the bolt head and the leak stopped.

Agree also with the suggestion that unless the engine breathing is set up properly it will blow oil. Can't see a PCV set up in that rocker cover. I have the same cover that I put a BSB thread and 90 degree angle output and plumbed it in with a toyota PCV (under advice from DrMini) to the manifold.

Cheers


Dave, any chance you could throw up a photo of your set-up for the PCV.

P.S. So the hole in the top of the cap and the breather tube attached to the rear cover doesn't stand for much?

Thanks

_________________
Dalmeny
Top
 Profile  
 
74snail
 Post subject:
PostPosted: Sun Nov 06, 2011 1:06 pm 
Offline
1275cc
1275cc
User avatar

Joined: Wed Oct 01, 2008 11:02 pm
Posts: 2611
Location: werribee vic
As you can see I have a breather on the right near the radiator , my rocker cover is vented straight out , my engine is a factory standard bore 1100, factory cam but with a higher compression ( about 9:2 or 9:3.1 )with the change of head , I have no real need for another breather as the crankcase pressure even with hard use is about static , from what you are describing I would say that you need two breathers to reduce the crankcase pressure


Image


.

_________________
Image
Top
 Profile  
 
dodge
 Post subject:
PostPosted: Sun Nov 06, 2011 2:13 pm 
Offline
998cc
998cc

Joined: Tue Feb 07, 2006 7:34 am
Posts: 950
Location: brisvages
my leaking gaskets should have used silicoln
Image

_________________
A good friend will come and bail you out of jail...but a true friend will be sitting next to you saying "Damn...that was fun!"
Top
 Profile  
 
Morris 1100
 Post subject:
PostPosted: Sun Nov 06, 2011 2:18 pm 
Offline
Causing or creating vexation

Joined: Wed Jul 21, 2004 10:32 pm
Posts: 19124
Use Permatex (Loctite) No3. Leave the silicone for sealing the bathroom tiles.
Top
 Profile  
 
Callin
 Post subject:
PostPosted: Sun Nov 06, 2011 2:50 pm 
Offline
848cc
848cc
User avatar

Joined: Tue Mar 27, 2007 7:46 pm
Posts: 296
Location: Strathmore, Melbourne, VIC
my understanding with cork gaskets, rod covers and rocker cover alike, they should only be done up firmly. Too tight will squash them and cause leaks, if not deform the covers

Sounds as if as described you might need another breather because of excess pressure

_________________
'63 850/1100 + more cooper goodies
Top
 Profile  
 
Super-mini
 Post subject:
PostPosted: Sun Nov 06, 2011 2:56 pm 
Offline
Supercharged
User avatar

Joined: Mon Oct 13, 2008 3:09 pm
Posts: 1246
Location: Adelaide
you want to run plain water in a fresh engine for the run in period before going to coolant.
Top
 Profile  
 
drmini in aust
 Post subject:
PostPosted: Sun Nov 06, 2011 3:36 pm 
Offline
religious status
religious status
User avatar

Joined: Fri Mar 19, 2004 6:19 pm
Posts: 39754
Location: near Baulkham Hills, NSW
Dodge,
Did you change the square o-rings on those 2 bolts-- the late covers like these are more likely to leak there than the gasket.
The right gaskets for these late covers are NOT cork, they are red silicone rubber- used on Cooper S and 998 Clubby.
The cork and cork/rubber gaskets are for the early flat face covers only (size is different).

_________________
DrMini- 1970 wasaMatic 1360, Mk1S crank, 86.6HP (ATW) =~125 @ crank, 45 Dellorto (38 chokes), RE282 sprint cam, 1.5 rockers, 11.0:1 C/R. :mrgreen:
Top
 Profile  
 
dalmeny
 Post subject:
PostPosted: Sun Nov 06, 2011 7:41 pm 
Offline
848cc
848cc
User avatar

Joined: Fri Jul 01, 2011 3:20 pm
Posts: 460
Location: Goulburn NSW
Super-mini wrote:
you want to run plain water in a fresh engine for the run in period before going to coolant.


Got that info from John Smidt after I arrived at his place with the coolant in. Is there any point in putting water in now after 200 miles with coolant?

_________________
Dalmeny
Top
 Profile  
 
drmini in aust
 Post subject:
PostPosted: Sun Nov 06, 2011 7:44 pm 
Offline
religious status
religious status
User avatar

Joined: Fri Mar 19, 2004 6:19 pm
Posts: 39754
Location: near Baulkham Hills, NSW
I don't think so. The main idea of using water is in case there are initial leaks.
If it's not leaking now I'd just retighten the head, and carry on. :wink:

_________________
DrMini- 1970 wasaMatic 1360, Mk1S crank, 86.6HP (ATW) =~125 @ crank, 45 Dellorto (38 chokes), RE282 sprint cam, 1.5 rockers, 11.0:1 C/R. :mrgreen:
Top
 Profile  
 
dalmeny
 Post subject:
PostPosted: Sun Nov 06, 2011 7:52 pm 
Offline
848cc
848cc
User avatar

Joined: Fri Jul 01, 2011 3:20 pm
Posts: 460
Location: Goulburn NSW
As usual you guys are right again.

I cleaned it up and took it for another run and it looks like the oil is being sprayed out of the squashed breather pipe in the rear cover plate. Do I need to put the original tappet cover on and feed a hung of hose down towards the road or do I drill the alloy cover and fit a PCV and run it into the manifold. Does it have to be balanced between the two inlets, or can it just tap into the one side of the inlet?

If there is a thread on here about the set up can you let me known.

_________________
Dalmeny
Top
 Profile  
 
dalmeny
 Post subject:
PostPosted: Sun Nov 06, 2011 7:54 pm 
Offline
848cc
848cc
User avatar

Joined: Fri Jul 01, 2011 3:20 pm
Posts: 460
Location: Goulburn NSW
drmini in aust wrote:
I don't think so. The main idea of using water is in case there are initial leaks.
If it's not leaking now I'd just retighten the head, and carry on. :wink:


Thanks drmini any thoughts on the "clack clack"noise that goes when you push the clutch in!!

_________________
Dalmeny
Top
 Profile  
 
Morris 1100
 Post subject:
PostPosted: Sun Nov 06, 2011 8:05 pm 
Offline
Causing or creating vexation

Joined: Wed Jul 21, 2004 10:32 pm
Posts: 19124
Does it do it with the motor stopped?
Top
 Profile  
 
dalmeny
 Post subject:
PostPosted: Sun Nov 06, 2011 8:12 pm 
Offline
848cc
848cc
User avatar

Joined: Fri Jul 01, 2011 3:20 pm
Posts: 460
Location: Goulburn NSW
Morris 1100 wrote:
Does it do it with the motor stopped?


Morrie!! What does that mean? It's perfectly quiet with the motor off.

_________________
Dalmeny
Top
 Profile  
 
drmini in aust
 Post subject:
PostPosted: Sun Nov 06, 2011 8:28 pm 
Offline
religious status
religious status
User avatar

Joined: Fri Mar 19, 2004 6:19 pm
Posts: 39754
Location: near Baulkham Hills, NSW
dalmeny wrote:
drmini in aust wrote:
I don't think so. The main idea of using water is in case there are initial leaks.
If it's not leaking now I'd just retighten the head, and carry on. :wink:


Thanks drmini any thoughts on the "clack clack"noise that goes when you push the clutch in!!

yeah it's 90% bound to be primary gear rattle. Won't hurt it...
Caused by- slow idle, light flywheel, big cam, too much endfloat on primary gear, gear wear, etc.

_________________
DrMini- 1970 wasaMatic 1360, Mk1S crank, 86.6HP (ATW) =~125 @ crank, 45 Dellorto (38 chokes), RE282 sprint cam, 1.5 rockers, 11.0:1 C/R. :mrgreen:
Top
 Profile  
 
9YaTaH
 Post subject: Re: What's going on????
PostPosted: Sun Nov 06, 2011 8:36 pm 
Offline
1360cc
1360cc
User avatar

Joined: Sun Apr 11, 2004 11:32 am
Posts: 12390
Location: Sthrn HiLoLands, NSW, Australia
miniDave wrote:

If your covers are the ones that rise outwards with the bolt on the peak then you need to seal around the bolt head. There is a rubber/felt washer as new but I put some RTV Grey gasket maker under the bolt head and the leak stopped.

Cheers


and check that they haven't been over torqued at some stage and the rise is squashed or no more...check that the flat sections around the rim are flat against the block (before you put the gasket on)

_________________
"Show me the Mini!"
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 2 of 3
  [ 39 posts ]  Go to page Previous  1, 2, 3  Next

Board index » Mini Chat » Mini Chat

All times are UTC + 10 hours


Who is online

Users browsing this forum: No registered users and 75 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  

© 2016 Ausmini. All garage work involves equal measures of enthusiasm, ingenuity and a fair degree of irresponsibility.