Ausmini
It is currently Tue Aug 12, 2025 7:50 am

Board index » Mini Chat » Mini Chat

All times are UTC + 10 hours




Post new topic Reply to topic  Page 1 of 1
  [ 14 posts ] 
  Print view Previous topic | Next topic 
Author Message
SteveOB
 Post subject: radiator removal
PostPosted: Wed Mar 21, 2012 6:18 pm 
Offline
848cc
848cc
User avatar

Joined: Mon Sep 05, 2011 7:50 pm
Posts: 364
Location: Wollongong NSW
I've looked it up - even did it about 15 years ago, but it took me half a day and lots of swearing and knuckles scraped

seriously, how easy/hard is it (surely not half a day!) and is it easier to remove the lot (ie shroud and all) in one go??

mine needs an overhaul or replacement so am gonna have to do it soon

cheers!
Top
 Profile  
 
ryan
 Post subject: Re: radiator removal
PostPosted: Wed Mar 21, 2012 6:24 pm 
Offline
1275cc
1275cc

Joined: Wed Jan 05, 2005 4:50 pm
Posts: 2690
Location: Wollongong
Quote:
Another way of removing the radiator provided by Matt Read .

The MiniMan wrote:
Removing the Mini Radiator

OK ,,, before this blows out into a frenzy of people stuffing with their radiator shrouds,,, the mini radiator is already an "Easy-out" item if you know how

There’s a simple standard easy way,,,, & then there is the "usual" misinformed , time consuming, head ache, pain in the arse way

Listen (read) & learn

Firstly, you take the 2 engine mount bolts & nuts out from the passengers side,,, then jack the engine up on that side,

2ndly you undo & remove the 2 vertical bolts that mount the bottom radiator bracket to the engine mount bracket (Not the 2 bolts that are located side ways through the lower radiator bracket to the lower radiator cowl, just leave them there),

then with the top radiator bracket & both top & bottom radiator hoses un-clamped, it’s just a matter of lifting the whole assembly, radiator with cowls attached , in one big bit, straight up & out of the hole... easy-peasy

the factory even made the later radiator cowls one piece because there really was never any reason the make it 2 pieces in the first place (except to fool the un-initiated)

It’s that easy,,, the Morris 1100 ones are even easier as they only have one bolt at the bottom.

A weenie bit of patience & a tad of practice & common sense & your radiator will be out in about 5 mins flat... & back in about 8 mins

Not all weekend like some do trying to remove all the cowl screws & removing it separately,,, WRONG!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

sorry but this topic really gets my back up , because it’s so easy & quick doing it the "CORRECT" way

ok,,, rant over, & again sorry but dam!!!!!!!!!!!!!!!!!!!!

no offence to anyone intended, I just mean this post as a help to any & all who listen to ideas of modifying things that just really don’t need modifying.
_________________
MadMatt "Ready" Read---> "The MiniMan"


Hope this helps

_________________
Ryan Filippi
Minis In The Gong
[email protected]
www.minisinthegong.com.au
Top
 Profile  
 
Fiji
 Post subject:
PostPosted: Thu Mar 22, 2012 11:45 pm 
Offline
1098cc
1098cc

Joined: Mon Jul 10, 2006 5:59 pm
Posts: 1275
Location: Bris / Syd
Yep that's it . Easy peAsey, as the
Man himself would say. It is that easy . 20 mins eather way. G l

_________________
PrOuDlY aSkInG qUeStIoNs FoR uR aMuEsMeNt
Top
 Profile  
 
SteveOB
 Post subject: radiator removal
PostPosted: Tue Apr 10, 2012 11:16 am 
Offline
848cc
848cc
User avatar

Joined: Mon Sep 05, 2011 7:50 pm
Posts: 364
Location: Wollongong NSW
20 minutes eh??

have been under, in and around it now for near on an hour!!

any clues on the best engine jacking points please so I can at least get a spanner into that tight spot for the two engine mount bolts??

cheers!
Top
 Profile  
 
NG
 Post subject:
PostPosted: Tue Apr 10, 2012 11:49 am 
Offline
1098cc
1098cc
User avatar

Joined: Wed Oct 01, 2008 11:14 am
Posts: 1906
Location: Brisbane Qld, North side
gearbox.. put a bock of wood on it when jacking onto the box..

works perfect takes me about 35mins out.
Top
 Profile  
 
origmini
 Post subject: Radiator Removal
PostPosted: Tue Apr 10, 2012 11:50 am 
Offline
848cc
848cc

Joined: Sat Jun 20, 2009 6:27 am
Posts: 124
.Sorry


Last edited by origmini on Tue Apr 10, 2012 12:30 pm, edited 1 time in total.

Top
 Profile  
 
SteveOB
 Post subject: radiator removal
PostPosted: Tue Apr 10, 2012 11:57 am 
Offline
848cc
848cc
User avatar

Joined: Mon Sep 05, 2011 7:50 pm
Posts: 364
Location: Wollongong NSW
ok so several skinned knuckles later I have now managed to get the two engine mount bolts free from the bracket to the radiator

now I am stuck on how the hell it slips up past the fan and the side of the car without taking off the shroud?

surely the shroud has to come off no?
Top
 Profile  
 
SteveOB
 Post subject: radiator removal
PostPosted: Tue Apr 10, 2012 11:58 am 
Offline
848cc
848cc
User avatar

Joined: Mon Sep 05, 2011 7:50 pm
Posts: 364
Location: Wollongong NSW
oh and it's on a mini-matic if that makes any difference (not sure sorry!)
Top
 Profile  
 
SteveOB
 Post subject:
PostPosted: Tue Apr 10, 2012 12:26 pm 
Offline
848cc
848cc
User avatar

Joined: Mon Sep 05, 2011 7:50 pm
Posts: 364
Location: Wollongong NSW
aa haaaa!!

stoopid me had the car jacked up AND the engine too!!

dropped the car, radiator popped out - it can be done - wish I knew this when I did it years ago, and I didn't even have to take off the bonnet this time too

thanks Mini folkers, am off to get it overhauled, new cap and a fan too while it's off methinks
Top
 Profile  
 
simon k
 Post subject:
PostPosted: Tue Apr 10, 2012 3:58 pm 
Offline
Yay For Hay!
User avatar

Joined: Wed Sep 08, 2004 9:27 pm
Posts: 15912
Location: Wodonga - Vic/NSW border
weld the nuts on to the engine mount before you put it back in too...
Top
 Profile  
 
1071 S
 Post subject:
PostPosted: Tue Apr 10, 2012 6:40 pm 
Offline
998cc
998cc

Joined: Fri Apr 01, 2011 8:33 pm
Posts: 1196
"..weld the nuts on to the engine mount before you put it back in too..."

Been there, done that...wouldn't do it again...

With loose nuts you can wiggle/screw the bolts through the holes then fit the nuts. With welded nuts you have to line the holes (subbie/mounts) up perfectly and then get the bolt at a perfect angle to engage the threads... Oh, and you end up with the bolts wrong end up as well...

Cheers, Ian
Top
 Profile  
 
SteveOB
 Post subject: radiator removal
PostPosted: Tue Apr 10, 2012 7:14 pm 
Offline
848cc
848cc
User avatar

Joined: Mon Sep 05, 2011 7:50 pm
Posts: 364
Location: Wollongong NSW
was wondering why I'd wanna weld the nuts in

I found if I laid a certain way, closed my eyes and twiddled me nuts, all seemed good

hope the radiator goes back in as well tho

;)

Am still made up it came out so easy. Plus, on a MITG recommendation, took it to Unanderra Radiators for an overhaul - they told me she looks blocked, will give it a going over, should be ready by 2pm tomorrow for $70 thanks

plus already ordered a new fan and radiator cap from John at the Mini King too

good old easter hols so far so good!
Top
 Profile  
 
drmini in aust
 Post subject:
PostPosted: Tue Apr 10, 2012 7:36 pm 
Offline
religious status
religious status
User avatar

Joined: Fri Mar 19, 2004 6:19 pm
Posts: 39764
Location: near Baulkham Hills, NSW
1071 S wrote:
"..weld the nuts on to the engine mount before you put it back in too..."

Been there, done that...wouldn't do it again...

With loose nuts you can wiggle/screw the bolts through the holes then fit the nuts. With welded nuts you have to line the holes (subbie/mounts) up perfectly and then get the bolt at a perfect angle to engage the threads... Oh, and you end up with the bolts wrong end up as well...

Cheers, Ian

[puts on flameproof suit]
Been doing this since 1966, it works for me. I used to tack `em with the old arc welder, now I use the MIG.
Just watch they are spaced at the right centres for your subframe holes, I use a jig to align the bolts/nuts.
They are not hard to align with the subby holes- use a #2 Phillips or Posidriv screwdriver, it won't hurt the threads.

_________________
DrMini- 1970 wasaMatic 1360, Mk1S crank, 86.6HP (ATW) =~125 @ crank, 45 Dellorto (38 chokes), RE282 sprint cam, 1.5 rockers, 11.0:1 C/R. :mrgreen:
Top
 Profile  
 
1275LS
 Post subject:
PostPosted: Tue Apr 10, 2012 7:45 pm 
Offline
998cc
998cc
User avatar

Joined: Mon Sep 07, 2009 3:11 pm
Posts: 749
Location: Brisbane northside
To updates Matt's instructions:

    Jack the car up and place on a short stand or sturdy wood block.
    Remove the road wheel.
    Take the 2 engine mount bolts & nuts out from the passenger’s side by undoing the nuts in the wheel arch.
    Jack the engine up on the passenger’s side until the 2 bolt heads for the radiator bracket on top of the engine mount are easily accessible from the wheel arch. This also helps when lifting the Radiator out
    Undo & remove the 2 vertical bolts that mount the bottom radiator bracket to the engine mount bracket - not the 2 bolts that are located sideways through the lower radiator bracket to the lower radiator cowl.
    Remove the top radiator bracket .
    Unclamp both top & bottom radiator hoses
    Tilt the radiator sideways so the bottom goes towards the wheel and the top goes towards the engine if it is snug on the fan and wiggle it out.

As the Mini Man would say – Easy peasy!

I did this today. No worries..

_________________
Cheers
Alec
1275LS - July 78 - XNFAD18Y/102918
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 14 posts ] 

Board index » Mini Chat » Mini Chat

All times are UTC + 10 hours


Who is online

Users browsing this forum: goodie and 149 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  

© 2016 Ausmini. All garage work involves equal measures of enthusiasm, ingenuity and a fair degree of irresponsibility.